Cisco Catalyst 3560-E Series Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 150

background image

2-38

Catalyst 3750-X, 3750-E, 3560-X, and 3560-E Switch System Message Guide

OL-9772-05

Chapter 2 Message and Recovery Procedures

GBIC_SECURITY_CRYPT Messages

GBIC_SECURITY_CRYPT Messages

Note

The Catalyst 3750-X, 3750-E, 3560-X, and 3560-E switches support SFP and 10-Gigabit Ethernet
modules but do not support GBIC modules. Although the error message text refers to GBIC interfaces
and modules, the messages from the switches actually refer to the SFP and 10-Gigabit Ethernet module
interfaces and modules.

Error Message

GBIC_SECURITY_CRYPT-4-ID_MISMATCH: Identification check failed for

GBIC in port [chars]

Explanation

The SFP module was identified as a Cisco SFP module, but the system could not verify

its identity. [chars] is the port.

Recommended Action

Ensure that the Cisco IOS software running on the switch supports the SFP

module. You might need to upgrade your software. Otherwise, verify that the SFP module was
obtained from Cisco or from a supported vendor.

Error Message

GBIC_SECURITY_CRYPT-4-UNRECOGNIZED_VENDOR: GBIC in port [chars]

manufactured by an unrecognized vendor

Explanation

The SFP module was identified as a Cisco SFP module, but the switch could not match

its manufacturer with one on the known list of Cisco SFP module vendors. [chars] is the port.

Recommended Action

Ensure that the Cisco IOS software running on the switch supports the SFP

module. You might need to upgrade your software.

Error Message

GBIC_SECURITY_CRYPT-4-VN_DATA_CRC_ERROR: GBIC in port [chars] has bad

crc

Explanation

The SFP module was identified as a Cisco SFP module, but it does not have a valid

cyclic redundancy check (CRC) in the EEPROM data. [chars] is the port.

Recommended Action

Ensure that the Cisco IOS software running on the switch supports the SFP

module. You might need to upgrade your software. Even if the SFP module is unrecognized by the
switch, the SFP module might still operate properly but have limited functionality.

«
...
54
55
56
57
58
...
»

Содержание Catalyst 3560-E Series























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 3560-E Series

Бренд: Hal Communications Страницы: 25

grandMA2 Series

Бренд: MA lighting Страницы: 36

Бренд: National Instruments Страницы: 9

Бренд: Lancom Страницы: 102

Бренд: vPipes Страницы: 3

Бренд: A4Tech Страницы: 7

Бренд: 3Ware Страницы: 4

8677 - BladeCenter Rack-mountable - Power Supply

Бренд: IBM Страницы: 126

Бренд: E-LINX Страницы: 24

Бренд: Z-Wave Страницы: 6

Бренд: ADTRAN Страницы: 2

FastTrak TX4000

Бренд: Promise Technology Страницы: 76

Compact NVR-AS 4000

Бренд: IndigoVision Страницы: 38

Бренд: ICP DAS USA Страницы: 8

Бренд: Penguin Edge Страницы: 2

Aquaduct 240 eco

Бренд: Aqua Computer Страницы: 20

640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU

Бренд: Intel Страницы: 105

JetFusion 2100 Series

Бренд: Paradyne Страницы: 296

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды