manualshive.com logo in svg

Altera UG-01080, Руководство пользователя

Поделиться
Скачать
Altera UG-01080 Скачать руководство пользователя страница 678

Date

Document

Version

Changes Made

March 2013

2.0

Made the following changes:
• Improved the description of automatic speed detection.

• Updated speed grade information.

• Updated definition of 

KR AN Link Ready[5:0]

 to include

1000BASE-KX.

• Added the following registers 

SEQ LT timeout

 at 0xB1, Bit 2

and 

SEQ Reconfig Mode[5:0] 

0xB1, Bits[13:8] registers

• Revised Functional Description section.

• Corrected typos in specifications of address bits 

Ovride LP

Coef enable

 , 

Updated TX Coef new

and 

Updated RX coef

new

 .

• Corrected encodings for 

ber_time_k_frames

, 

ber_time_

frames

 and 

ber_time_m_frames

.

1Gbe/10GbE

March 2013

2.0

Made the following changes:
• Updated speed grade information.

• Removed definition of 

Disable AN Timer

 bit. It is not used for

this variant.

• Added fact that 

RESTART_AUTO_NEGOTIATION

 bit is self-clearing

(0x90, bit 9)

• Added fact that half-duplex mode is not supported. (0x94, bit 6)

• Added fact that the next page bit is not supported. (0x94, bit 15)

XAUI

March 2013

2.0

Added Arria V, Arria V GZ and Cyclone V to the list of devices that

do not support the 

pma_tx_pll_is_locked

 register in Table 6-15:

XAUI PHY IP Core Registers.

Interlaken

March 2013

2.0

No changes from previous release.

PHY IP Core for PCI Express

March 2013

2.0

Added SDC constraints for Gen3 clocking.

Custom PHY

March 2013

2.0

No changes from previous release.

Low Latency PHY

March 2013

2.0

No changes from previous release.

Deterministic Latency PHY

March 2013

2.0

No changes from previous release.

21-18

Revision History for Previous Releases of the Transceiver PHY IP Core

UG-01080

2015.01.19

Altera Corporation

Additional Information for the Transceiver PHY IP Core

Send Feedback

Содержание UG-01080































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды