manualshive.com logo in svg

Altera UG-01080, Руководство пользователя

Поделиться
Скачать
Altera UG-01080 Скачать руководство пользователя страница 381

Table 13-4: TX PMA Parameters

Parameter

Range

Description

Enable TX PLL dynamic

reconfiguration

On/Off

When you turn this option On, you can dynamically

reconfigure the PLL. This option is also required to

simulate TX PLL reconfiguration. If you turn this option

On, the Quartus II Fitter prevents PLL merging by

default; however, you can specify merging using the

XCVR_TX_PLL_RECONFIG_GROUP

 QSF assignment.

Use external TX PLL

On/Off

When you turn this option On, the Native PHY does not

automatically instantiate a TX PLL. Instead, you must

instantiate an external PLL and connect it to the 

ext_

pll_clk[<p> -1 : 0]

 port of the Arria V Native PHY.

Use the Arria V Transceiver PLL IP Core to instantiate a

CMU PLL. Use Altera Phase-Locked Loop (ALTERA_

PLL) Megafunction to instantiate a fractional PLL.

Number of TX PLLs

1–4

Specifies the number of TX PLLs that can be used to

dynamically reconfigure channels to run at multiple data

rates. If your design does not require transceiver TX PLL

dynamic reconfiguration, set this value to 1. The number

of actual physical PLLs that are implemented depends on

the selected clock network. Each channel can

dynamically select between n PLLs, where n is the

number of PLLs specified for this parameter.
Note: Refer to 

Transceiver Clocking in Arria V

Devices

 chapter for more details.

Main TX PLL logical

index

0–3

Specifies the index of the TX PLL used in the initial

configuration.

Number of TX PLL

reference clocks

1–5

Specifies the total number of reference clocks that are

used by all the PLLs.

Related Information

Transceiver Clocking in Arria V Devices

TX PLL Parameters

This section allows you to define multiple TX PLLs for your Native PHY. The Native PHY GUI provides a

separate tab for each TX PLL.

13-6

TX PLL Parameters

UG-01080

2015.01.19

Altera Corporation

Arria V Transceiver Native PHY IP Core

Send Feedback

Содержание UG-01080































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды