Altera UG-01080 Скачать руководство пользователя | Manualshive

Страница: 183 / 702

background image

Interlaken PHY Register Interface and Register Descriptions

This section describes the register interface and register descriptions.
The Avalon-MM PHY management interface provides access to the Interlaken PCS and PMA registers,

resets, error handling, and serial loopback controls. You can use an embedded controller acting as an

Avalon-MM master to send read and write commands to this Avalon-MM slave interface.

Table 7-9: Avalon-MM PCS Management Interface

Signal Name

Direction

Description

phy_mgmt_clk

Input

Avalon-MM clock input.
There is no frequency restriction for Stratix V devices;

however, if you plan to use the same clock for the PHY

management interface and transceiver reconfigura‐

tion, you must restrict the frequency range of

phy_

mgmt_clk

to 100–150 MHz to meet the specification

for the transceiver reconfiguration clock.

phy_mgmt_clk_reset

Input

Global reset signal that resets the entire Interlaken

PHY. This signal is active high and level sensitive.
When the Interlaken PHY IP connects to the

Transceiver PHY Reconfiguration Controller IP Core,

the Transceiver PHY Reconfiguration Controller

mgmt_rst_reset

signal must be simultaneously

asserted with the

phy_mgmt_clk_reset

signal to bring

the Frame Generators in the link into alignment. This

is a mandatory requirement. Failure to comply to this

requirement will result in excessive transmit lane-to-

lane skew in the Interlaken link.

phy_mgmt_addr[8:0]

Input

9-bit Avalon-MM address.

phy_mgmt_writedata[31:0]

Input

Input data.

phy_mgmt_readdata[31:0]

Output

Output data.

phy_mgmt_write

Input

Write signal.

phy_mgmt_read

Input

Read signal.

phy_mgmt_waitrequest

Output

When asserted, indicates that the Avalon-MM slave

interface is unable to respond to a read or write

request. When asserted, control signals to the Avalon-

MM slave interface must remain constant.

The following table specifies the registers that you can access using the Avalon-MM PHY management

interface using word addresses and a 32-bit embedded processor. A single address space provides access

to all registers. Writing to reserved or undefined register addresses may have undefined side effects.
Note: All undefined register bits are reserved.

7-16

Interlaken PHY Register Interface and Register Descriptions

UG-01080

2015.01.19

Altera Corporation

Interlaken PHY IP Core

Send Feedback

«
...
181
182
183
184
185
...
»

Содержание UG-01080































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для UG-01080

Бренд: Cabletron Systems Страницы: 26

Бренд: Campbell Страницы: 50

Бренд: Fairchild Страницы: 4

Бренд: Fairchild Страницы: 2

Бренд: Offshore Страницы: 14

Бренд: XIEGU Страницы: 20

Бренд: XIEGU Страницы: 17

ZR-4630 ZR-4630

Бренд: Niles Страницы: 82

ZR-4630 ZR-4630

Бренд: Niles Страницы: 82

Бренд: ADTRAN Страницы: 24

Бренд: Comtek Страницы: 18

Бренд: FTE Maximal Страницы: 44

Бренд: Yaesu Страницы: 96

Бренд: Radio Shack Страницы: 11

Tomorrow's Weather Today TX29U

Бренд: La Crosse Technology Страницы: 2

Бренд: ADTRAN Страницы: 17

Бренд: Nav TV Страницы: 2

Бренд: Hallicrafters Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды