Altera UG-01080 страница 188 Скачать руководство пользователя | Manualshive

Страница: 188 / 702

background image

Signal Name

Direction

Description

reconfig_from_xcvr

[(<n>46)-1:0]

Output

Reconfiguration signals to the Transceiver Reconfiguration

Controller. <

n

> grows linearly with the number of reconfigura‐

tion interfaces. <

n

> initially includes the total number

transceiver channels before optimization/merging.

Note: Transceiver dynamic reconfiguration requires that you assign the starting channel number.

Interlaken PHY TimeQuest Timing Constraints

This section describes the Interlaken PHY TimeQuest timing constraints.
You must add the following TimeQuest constraint to your Synopsys Design Constraints File (.sdc) timing

constraint file:

derive_pll_clocks -create_base_clocks

Note: The SDC timing constraints and approaches to identify false paths listed for Stratix V Native PHY

IP apply to all other transceiver PHYs listed in this user guide. Refer to

SDC Timing Constraints of

Stratix V Native PHY

for details.

Related Information

SDC Timing Constraints of Stratix V Native PHY

on page 12-74

This section describes SDC examples and approaches to identify false timing paths.

Interlaken PHY Simulation Files and Example Testbench

This section describes the Interlaken PHY simulation files and example testbench.
Refer to “ Running a Simulation Testbench” for a description of the directories and files that the Quartus

II software creates automatically when you generate your Interlaken PHY IP Core.
Refer to the Altera Wiki for an example testbench that you can use as a starting point in creating your

own verification environment.

Related Information

•

Running a Simulation Testbench

on page 1-6

•

Altera Wiki

UG-01080

2015.01.19

Interlaken PHY TimeQuest Timing Constraints

7-21

Interlaken PHY IP Core

Altera Corporation

Send Feedback

«
...
186
187
188
189
190
...
»

Содержание UG-01080































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для UG-01080

Beolab transmitter 1

Бренд: Bang & Olufsen Страницы: 30

Бренд: M-system Страницы: 3

Бренд: Alan Страницы: 6

Бренд: Strong Страницы: 15

Mini-LCD Transmitter TX-MLCD

Бренд: AMX Страницы: 22

Бренд: Icom Страницы: 7

Бренд: Hallicrafters Страницы: 9

Бренд: XRadio Страницы: 29

Бренд: JAMO Страницы: 142

Бренд: JastecM Страницы: 2

Бренд: Comet Страницы: 18

Бренд: Nokeval Страницы: 38

WireLess 101-050-80125

Бренд: OMFB Страницы: 35

Бренд: Vaisala Страницы: 16

MCT/IR-252 WP S

Бренд: SpiderAlert Страницы: 2

Бренд: Portech Страницы: 8

Бренд: Extron electronics Страницы: 37

SEL2641 R433-Z2

Бренд: Erone Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды