Altera UG-01080 страница 238 Скачать руководство пользователя

Страница: 238 / 702

Signal Name

Direction

Signal Name

rx_errdetect[<n>(<w>/<s>)-1:0]

Output

When asserted, indicates that a

received 10-bit code group has an 8B/

10B code violation or disparity error.

rx_syncstatus[ <n> (<w>/<s>)-

1:0]

Output

Indicates presence or absence of

synchronization on the RX interface.

Asserted when word aligner identifies

the word alignment pattern or

synchronization code groups in the

received data stream. This signal is

optional.

rx_is_lockedtoref[ <n> -1:0]

Output

Asserted when the receiver CDR is

locked to the input reference clock.

This signal is asynchronous. This

signal is optional.

rx_is_lockedtodata[ <n> -1:0]

Output

When asserted, the receiver CDR is in

to lock-to-data mode. When

deasserted, the receiver CDR lock

mode depends on the

rx_locktor-

efclk

signal level. This signal is

optional.

rx_signaldetect[ <n> -1:0]

Output

Signal threshold detect indicator

required for the PCI Express

protocol. When asserted, it indicates

that the signal present at the receiver

input buffer is above the

programmed signal detection

threshold value.

rx_bitslip[ <n> -1:0]

Input

Used for manual control of bit

slipping. The word aligner slips a bit

of the current word for every rising

edge of this signal. This is an

asynchronous input signal and inside

there is a synchronizer to synchronize

it with

rx_pma_clk/rx_clkout

rx_bitslipboundaryselectout

[ <n> 5-1:0]

Output

This signal is used for bit slip word

alignment mode. It reports the

number of bits that the RX block

slipped to achieve a deterministic

latency.

rx_patterndetect[<n>(<w>/<s>)-

1:0]

Output

When asserted, indicates that the

programmed word alignment pattern

has been detected in the current word

boundary.

UG-01080

2015.01.19

Optional Status Interface

9-25

Custom PHY IP Core

Altera Corporation

Send Feedback

Содержание UG-01080































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание UG-01080

Отзывы:

Похожие инструкции для UG-01080

Бренды по названию

Популярные бренды

Altera UG-01080, Руководство пользователя

Результаты поиска

Содержание UG-01080

Отзывы:

Похожие инструкции для UG-01080

Бренды по названию

Популярные бренды