Altera UG-01080 страница 260 Скачать руководство пользователя

Страница: 260 / 702

Related Information

Analog Parameters Set Using QSF Assignments

on page 19-1

Low Latency PHY Interfaces

The following figure illustrates the top-level signals of the Custom PHY IP Core. The variables in this

figure represent the following parameters:
• <n>—The number of lanes

• <w>—The width of the FPGA fabric to transceiver interface per lane

Figure 10-2: Top-Level Low Latency Signals

Low Latency PHY IP Core Top-Level Signals

tx_serial_data

<n>

rx_serial_data

<n>

rx_is_lockedtodata[

<n>-1:0]

rx_is_lockedtoref[

<n>-1:0]

pll_locked[ <n>-1:0]

tx_bitslip

rx_bitslip

pll_powerdown

tx_digitalreset

<n>

tx_analogreset

<n>

tx_cal_busy

<n>

rx_digitalreset

<n>

rx_analogreset

<n>

rx_cal_busy

<n>

reconfig_to_xcvr[(

<n>70-1):0]

reconfig_from_xcvr[(

<n>46-1):0]

Control and

Status

(Optional)

tx_parallel_data[

<n><w>-1:0]

tx_clkout[ <n>-1:0]

rx_parallel_data[

<n><w>-1:0]

rx_clkout[ <n>-1:0]

tx_ready[ <n>-1:0]

rx_ready[ <n>-1:0]

phy_mgmt_clk

phy_mgmt_clk_reset

phy_mgmt_address[8:0]

phy_mgmt_writedata[31:0]

phy_mgmt_readdata[31:0]

phy_mgmt_write

phy_mgmt_read

phy_mgmt_waitrequest

pll_ref_clk

tx_coreclkin[

<n>-1:0]

rx_coreclkin[

<n>-1:0]

Avalon-MM PHY

Management

Interface

Avalon-ST TX and RX

to and from MAC

Serial

Data

Dynamic

Reconfiguration

Reset Control

and Status

(Optional)

Clocks

Optional

Note: By default block diagram shown in the MegaWizard Plug-In Manager labels the external pins with

the

interface type

and places the

interface name

inside the box. The interface type and name are

used in the _hw.tcl file that describes the component. If you turn on Show signals, the block

diagram displays all toplevel signal names.

For more information about _hw.tcl files refer to refer to the

Component Interface Tcl Reference

chapter in volume 1 of the Quartus II Handbook.

Low Latency PHY Data Interfaces

The following table describes the signals in the Avalon-ST interface. This interface drives AvalonST TX

and RX data to and from the FPGA fabric. These signals are named from the point of view of the MAC so

that the TX interface is an Avalon-ST sink interface and the RX interface is an Avalon-ST source.

UG-01080

2015.01.19

Low Latency PHY Interfaces

10-13

Low Latency PHY IP Core

Altera Corporation

Send Feedback

Содержание UG-01080































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание UG-01080

Отзывы:

Похожие инструкции для UG-01080

Бренды по названию

Популярные бренды

Altera UG-01080, Руководство пользователя

Результаты поиска

Содержание UG-01080

Отзывы:

Похожие инструкции для UG-01080

Бренды по названию

Популярные бренды