Altera UG-01080 страница 178 Скачать руководство пользователя

Страница: 178 / 702

Signal Name

Direction

Description

rx_parallel_data<n>

[64]

Output

When asserted, indicates that

rx_parallel_data<n>[63:0]

valid. When deasserted, indicates the

rx_parallel_data<n>

[63:0]

is invalid. This output is synchronous to the

rx_

coreclkin

clock domain.

The Interlaken PCS implements a gearbox between the PMA

and PCS interface. The

rx_parallel_data<n>[64]

port is

deasserted whenever the gearbox is in the invalid region. The

Interlaken MAC should not read

rx_parallel_data<n>[65,

63:0]

rx_parallel_data<n>[64]

is deasserted.

rx_parallel_data<n>

[65]

Output

Indicates whether

rx_parallel_data<n>[63:0]

represents

control or data. When deasserted,

rx_parallel_data<n>

[63:0]

is a data word. When asserted,

rx_paralleldata<n>

[63:0]

is a control word. This output is synchronous to the

rx_

coreclkin

clock domain.

The value of header synchronization bits[65:64] of the

Interlaken word identify whether bits[63:0] are Framing Layer

Control/Burst/IDLE Word or a data word. The value 2’b10

indicating a Framing Layer Control/Burst/IDLE Word is gray

encoded to the value 1’b1 and

rx_parallel_data<n>[65]

asserted by the Interlaken Receive PCS. The value 2’b01

indicating data word is gray encoded to the value 1’b0 and

rx_

parallel_data<n>[65]

is deasserted by the Interlaken Receive

PCS. The Framing Layer Control Words (Frame Sync,

Scrambler State, Skip, and Diag) are not discarded but are sent

to the Interlaken MAC for multi-lane alignment and deskew on

the lanes.

rx_parallel_data<n>

[66]

Output

This is an active-high synchronous status signal indicating that

block lock (frame synchronization) and frame lock (metaframe

boundary delineation) have been achieved. The Interlaken

MAC must use this signal to indicate that Metaframe synchro‐

nization has been achieved for this lane. You must use this

rx_

parallel_data[66]

as the primary frame synchronization

status flag and only use the optional

rx_parallel_data[70]

the secondary frame synchronization status flag. This output is

synchronous to the rx_coreclkin clock domain.
If the RX PCS FIFO reaches the empty state or is in an empty

state,

rx_parallel_data<n>[66]

Block Lock and Frame Lock

status signals are deasserted in the next clock cycle.

rx_

parallel_data<n>[70]

indicating metaframe lock and

rx_

parallel_data<n>[69]

indicating that the first Interlaken

synchronization word alignment pattern has been received

remain asserted.

UG-01080

2015.01.19

Interlaken PHY Avalon-ST RX Interface

7-11

Interlaken PHY IP Core

Altera Corporation

Send Feedback

Содержание UG-01080































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание UG-01080

Отзывы:

Похожие инструкции для UG-01080

Бренды по названию

Популярные бренды

Altera UG-01080, Руководство пользователя

Результаты поиска

Содержание UG-01080

Отзывы:

Похожие инструкции для UG-01080

Бренды по названию

Популярные бренды