manualshive.com logo in svg

Altera UG-01080, Руководство пользователя

"Altera UG-01080" - это продукт, для которого доступно бесплатное руководство пользователя. Пользователи могут скачать руководство с manualshive.com и получить полезную информацию по использованию данного устройства. Убедитесь, что ваше устройство всегда будет работать на максимальной производительности, пользуясь этим руководством.

Поделиться
Скачать
background image

Table 13-13: Byte Serializer and Deserializer Parameters

Parameter

Range

Description

Enable TX byte serializer On/Off

When you turn this option On, the PCS includes a TX

byte serializer which allows the PCS to run at a lower

clock frequency to accommodate a wider range of FPGA

interface widths.

Enable RX byte deserial‐

izer

On/Off

When you turn this option On, the PCS includes an RX

byte deserializer which allows the PCS to run at a lower

clock frequency to accommodate a wider range of FPGA

interface widths.

Related Information

Transceiver Architecture in Arria V Devices

8B/10B

The 8B/10B encoder generates 10-bit code groups from the 8-bit data and 1-bit control identifier.
In 8-bit width mode, the 8B/10B encoder translates the 8-bit data to a 10-bit code group (control word or

data word) with proper disparity. The 8B/10B decoder decodes the data into an 8-bit data and 1-bit

control identifier.
Note: For more information refer to the 

8B/10B Encoder

 and 

8B/10B Decoder 

sections in the 

Transceiver

Architecture in Arria V Devices.

Table 13-14: 8B/10B Encoder and Decoder Parameters

Parameter

Range

Description

Enable TX 8B/10B

encoder

On/Off

When you turn this option On, the PCS includes the 8B/

10B encoder.

Enable TX 8B/10B

disparity control

On/Off

When you turn this option On, the PCS includes

disparity control for the 8B/10B encoder. You force the

disparity of the 8B/10B encoder using the 

tx_forcedisp

and 

tx_dispval

 control signal.

Enable RX 8B/10B

decoder

On/Off

When you turn this option On, the PCS includes the 8B/

10B decoder.

Related Information

Transceiver Architecture in Arria V Devices

Rate Match FIFO

The rate match FIFO compensates for the very small frequency differences between the local system clock

and the RX recovered clock.
For more information refer to the Rate Match FIFO sections in the 

Transceiver Architecture in Arria V

Devices

.

UG-01080

2015.01.19

8B/10B

13-15

Arria V Transceiver Native PHY IP Core

Altera Corporation

Send Feedback

Содержание UG-01080































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для UG-01080

Javad TRIUMPH-3 Start Manual preview
TRIUMPH-3
Бренд: Javad Страницы: 16
Harman Kardon ARIA HK220 Owner'S Manual preview
ARIA HK220
Бренд: Harman Kardon Страницы: 8
Jogler JLT-6000 series Manual preview
JLT-6000 series
Бренд: Jogler Страницы: 16
Tevion MD 81157 Manual preview
MD 81157
Бренд: Tevion Страницы: 22
Camille Bauer SINEAX DME 440 Operating Instructions Manual preview
SINEAX DME 440
Бренд: Camille Bauer Страницы: 40
Yaesu FT-101E Instruction Manual preview
FT-101E
Бренд: Yaesu Страницы: 42
Ebtron Advantage III Gold Series Installation Manual preview
Advantage III Gold Series
Бренд: Ebtron Страницы: 24
Small Wonder Labs PSK-20 Instructions Manual preview
PSK-20
Бренд: Small Wonder Labs Страницы: 26
JAROLIFT TDRC-01 Operating Instructions preview
TDRC-01
Бренд: JAROLIFT Страницы: 4
Yaesu FT-250E Manual preview
FT-250E
Бренд: Yaesu Страницы: 44
Silicon Laboratories SI4830 Specification Sheet preview
SI4830
Бренд: Silicon Laboratories Страницы: 2
Endress+Hauser HART Proline 400 Brief Operating Instructions preview
HART Proline 400
Бренд: Endress+Hauser Страницы: 36
THine THCV242 Manual preview
THCV242
Бренд: THine Страницы: 53
Grundig DTR 5460 HD User Manual preview
DTR 5460 HD
Бренд: Grundig Страницы: 50
Hallicrafters HT-44 Operation And Maintenance Manual preview
HT-44
Бренд: Hallicrafters Страницы: 30
Xeos Alert Geomatics Resolute User Manual preview
Alert Geomatics Resolute
Бренд: Xeos Страницы: 65
KRUSE KRUSEGO Operating Instructions Manual preview
KRUSEGO
Бренд: KRUSE Страницы: 7
Eddystone R191 C Manual preview
R191 C
Бренд: Eddystone Страницы: 17

Бренды по названию

Популярные бренды

Загрузить еще бренды