YOKOGAWA TA720 User Manual Download Page 84

Page: 84 / 228

6-8

IM 704510-01E

6.4

Setting Inhibit

For a functional description, see 2.5.

Procedure

Press the SAMPLE key to display the Sample menu.

Inhibit does not appear when the sampling mode is set to inter-symbol interference

analysis and dual measurement function is used.

Selecting the Polarity

Press the Inhibit soft key to select the polarity.

Selecting the Inhibit Input Level

Press the INPUT key to display the Input menu.

Press the Setting soft key to display the Input Setting menu.

Press the Inhibit soft key.

Press the Level soft key to display the Level selection menu.

Press the soft key corresponding to the desired level.

Explanation

Selecting the Polarity

Select from the following. When set to OFF, the inhibit input is invalid.

•

Inhibits measurements while a positive signal is being applied to the inhibit

input terminal.

•

Inhibits measurements while a negative signal is being applied to the inhibit

input terminal.

Note

The time in which the inhibit input is valid is within the maximum sampling time from arming

activation.

Input Method of the Inhibit Signal

Apply a signal to the terminal marked INHIBIT on the front panel.

• Input impedance:

1 M

Ω

(typical value*)

• Input coupling:

• Inhibit level:

Using the above procedure, select 0 V, TTL (1.4 V), or

TTL/10 (0.14 V).

• Maximum input voltage:

40 V (DC+ACpeak)

• Minimum input pulse width: 30 ns

• Setup time:

30 ns (must precede the input signal by at least 30 ns for

the inhibit to be valid).

Typical value represents a typical or average value. It is not strictly warranted.

Summary of Contents for TA720





































































































































































































































Search results

Summary of Contents for TA720

Reviews:

Related manuals for TA720

Brands by name

Popular brands

YOKOGAWA TA720, User Manual

Search results

Summary of Contents for TA720

Reviews:

Related manuals for TA720

Brands by name

Popular brands