YOKOGAWA TA720 User Manual Download Page 54

Page: 54 / 228

3-7

IM 704510-01E

Before Starting Measurements

3.4

Turning ON/OFF the Power Switch

Items to be checked before turning ON the power

• Is the instrument properly installed? See section 3.2, “Installing the TA720”

• Is the power cord properly connected? See section 3.3, “Connecting to the Power”

Location of the Power Switch and ON/OFF Operation

The power switch is located at the lower left section of the front panel. The power switch

is a push button. Press once to turn it “ON” and press again to turn it “OFF.”

OFF

Note

Allow at least 10 s when turning ON the power switch after turning it OFF. Otherwise, the

screen may not show anything. In such case, turn OFF the power switch again, wait at least

10 s, and then turn ON the power switch.

Power ON Operation

The following initial operation is carried out when the power switch is turned ON. Front panel key

operations are disabled during this period. When the initial operation is complete, the display

screen (screen that appears when the DISPLAY key is pressed) appears.

• ROM Check

• DRAM Check

• SRAM Check

• SRAM Cal Check: Calibration data check

Note

If the instrument does not operate as described above when the power switch is turned ON,

turn OFF the power switch and check the following points.

•

Check that the power cord is plugged in properly.

•

Is the correct voltage coming to the power outlet? See section 3.3.

If the TA720 still fails to power up when the power switch is turned ON after checking these

points, it is probably a malfunction. Please contact your nearest YOKOGAWA dealer as

listed on the back cover of this manual for repairs.

For Making Accurate Measurements

In the installation condition indicated in section 3.2, allow the instrument to warm up for

at least 30 minutes after the power switch is turned ON

Shutdown Operation

When the power switch is turned OFF, the setup data is stored, but measured results

and statistical calculation results are not. Save necessary data beforehand such as to a

floppy disk (section 11.5 and 11.6).

Note

The lithium battery that is used to store data has a limited life span. If the lithium battery is low,

the TA720 no longer operates properly such as the improper indication of date/time, or inability

to store/recall measured data. If such symptoms appear, execute a self test (see section 14.4).

If a warning message “Low Battery” is indicated as a result of the self test, the lithium battery

must be replaced quickly. The user cannot replace the battery. For battery replacement,

contact your nearest YOKOGAWA dealer as listed on the back cover of this manual.

Summary of Contents for TA720





































































































































































































































Search results

Summary of Contents for TA720

Reviews:

Related manuals for TA720

Brands by name

Popular brands

YOKOGAWA TA720, User Manual

Search results

Summary of Contents for TA720

Reviews:

Related manuals for TA720

Brands by name

Popular brands