YOKOGAWA TA720 User Manual Download Page 195

Page: 195 / 228

14-4

IM 704510-01E

Error No.

Message

Description

Page

815

Sampling interval cannot be entered

Sampling interval cannot be specified when using

8-8

while Estimated T.

Estimated T. Changed to Measured T or switch the
window mode.

816

Cannot be specified in this measurement Cannot be specified in this measurement item.

–

item.

817

External Arming and block rest time/event External Arming and block rest time/event cannot be 6-5, 6-11
cannot be used together.

used together.

Error in System Operation (900 and higher)

Error No.

Message

Description

Page

906

Fan stopped.

The cooling fan has stopped.

–

Turn OFF the power immediately.

912

Fatal error in communications driver.

Communication driver error.

–

914

A communications time-out has occurred. Communication timeout error.

–

Warming Messages (0 to 99)

Error No.

Message

Description

Page

Sample number overflowed.

The number of samples exceeded the measurable

15-1

number of samples.

Time stamp data overflowed.

The time stamp data has exceeded the maximum

15-1

sampling time.

Measurement data overflowed.

Measured data exceeded the measurement range.

15-2 to 15-4

Measured T failure.

Failed to measure auto window T.

8-8

Estimated T failure.

Failed to estimate auto window T.

8-8

Rest time is too short.

6-11

No reference clock.

No reference clock is applied.

6-15

Failure during continuous measurement. Failed continuous measurement.

2-7

ISI analysis impossible.

Inter-symbol interference analysis cannot be

9-11

performed.

Sync pattern not found.

No match pattern found.

8-14

Warning Mark

As shown in the figure below, a warning mark appears when there is an error message

or warning message.

Warning mark

In this case, press the Error Log soft key in the menu that appears by pressing the

UTILITY key. An error log is displayed and you can view the list of error messages and

warning messages. If there are many messages and they do not fit in the window, turn

the rotary knob to scroll the list. For details on the operation, see the next section.

14.2 Messages

Summary of Contents for TA720





































































































































































































































Search results

Summary of Contents for TA720

Reviews:

Related manuals for TA720

Brands by name

Popular brands

YOKOGAWA TA720, User Manual

Search results

Summary of Contents for TA720

Reviews:

Related manuals for TA720

Brands by name

Popular brands