YOKOGAWA TA720 User Manual Download Page 7

Page: 7 / 228

IM 704510-01E

Make sure to comply with the precautions below. Not complying might result in injury or

death.

WARNING

• Power Supply

Before connecting the power cord, ensure that the source voltage matches the

rated supply voltage of the instrument and that it is within the maximum rated

voltage of the provided power cord.

• Power Cord and Plug

To prevent the possibility of electric shock or fire, be sure to use the power cord

supplied by YOKOGAWA. The main power plug must be plugged into an outlet

with a protective earth terminal. Do not invalidate this protection by using an

extension cord without protective earth grounding.

• Protective Grounding

Make sure to connect the protective earth to prevent electric shock before

turning ON the power. The power cord that comes with the instrument is a

three-pin type power cord. Connect the power cord to a properly grounded

three-pin outlet.

• Necessity of Protective Grounding

Never cut off the internal or external protective earth wire or disconnect the

wiring of the protective earth terminal. Doing so poses a potential shock hazard.

• Defect of Protective Grounding

Do not operate the instrument if the protective earth or fuse might be defective.

Make sure to check them before operation.

• Fuse

To avoid the possibility of fire, only use a fuse that has a rating (voltage, current,

and type) that is specified by the instrument. When replacing a fuse, turn OFF

the power switch and unplug the power cord. Never short the fuse holder.

• Do Not Operate in an Explosive Atmosphere

Do not operate the instrument in the presence of flammable liquids or vapors.

Operation in such environments constitutes a safety hazard.

• Do Not Remove Covers

The cover should be removed by YOKOGAWA’s qualified personnel only.

Opening the cover is dangerous, because some areas inside the instrument

have high voltages.

• External Connection

Securely connect the protective grounding before connecting to the item under

measurement or an external control unit.

Safety Precautions

Summary of Contents for TA720





































































































































































































































Search results

Summary of Contents for TA720

Reviews:

Related manuals for TA720

Brands by name

Popular brands

YOKOGAWA TA720, User Manual

Search results

Summary of Contents for TA720

Reviews:

Related manuals for TA720

Brands by name

Popular brands