YOKOGAWA TA720 User Manual Download Page 36

Page: 36 / 228

2-16

IM 704510-01E

Statistics Display (see section 7.4 for the operating procedure)

In time stamp mode or hardware histogram mode, statistical parameters within a specified area

can be computed, and the results can be displayed in a list.

This section mainly describes the display of the statistical calculation results. For a description of

the area for performing statistical calculations and the statistical calculation parameters, see

section 2.7, “Statistical Calculation and Inter-symbol Interference Analysis.”

The displayed results vary depending on the sampling mode.

When in time stamp mode

You can select to calculate the statistics from the histogram or time variation.

When calculating from the histogram

When calculating from time variation

Area for performing
statistical calculation

Statistical calculation
parameters

Statistical
values

Statistical calculation
parameters

Depending on the above selection, the statistical parameters that can be calculated vary.

• When histogram is selected

Average, Maximum, Minimum, Peak-Peak,

/Average,

/T, Deviation, Deviation/T,

Median, Mode

• When time variation is selected

T.Average, T.Maximum, T.Minimum, T.Peak-Peak, T.

, T.(

/Average), T.(P-P/

Average), T.RF

The area for performing statistical calculation can be set to Window (entire window),

Marker (area enclosed by markers), or Block (measurement block). In addition, when

the area for performing the statistical calculation is set to Block, and the source from

which the statistics are calculated is set to time variation (T.V.) on block-sampled data,

the statistics can be displayed for each block.

When in hardware histogram mode

Below are the statistical parameters that can be calculated. For a description of the

statistical calculation parameters, see section 2.7, “Statistical Calculation and Inter-

symbol Interference Analysis.”

Average, Maximum, Minimum, Peak-Peak, s, s/Average, s/T, Deviation, Deviation/T,

Median, Mode

The area for performing statistical calculation can be set to Window (entire window) or

Marker (area enclosed by markers).

When using multi window
with Window selected

Statistical calculation
parameters

Area for performing
statistical calculation

When using multi window
with ALL selected

Statistical
values

Window label

Statistical
values

2.6 Displaying the Measured/Calculated Results

Summary of Contents for TA720





































































































































































































































Search results

Summary of Contents for TA720

Reviews:

Related manuals for TA720

Brands by name

Popular brands

YOKOGAWA TA720, User Manual

Search results

Summary of Contents for TA720

Reviews:

Related manuals for TA720

Brands by name

Popular brands