YOKOGAWA TA720 User Manual Download Page 53 | Manualshive

Page: 53 / 228

background image

3-6

IM 704510-01E

3.3

Connecting to the Power

Before Connecting the Power

Make sure that you observe the following points before connecting the power. Failure to

do so may cause electric shock or damage to the instrument.

WARNING

• Before connecting the power cord, ensure that the source voltage matches the

rated supply voltage of the instrument and that it is within the maximum rated

voltage of the provided power cord.

• Connect the power cord after checking that the power switch of the instrument is

turned OFF.

• To prevent the possibility of electric shock or fire, always use the power cord

supplied by YOKOGAWA.

• Make sure to perform protective grounding to prevent the possibility of electric

shock. Connect the power cord to a three-pin power outlet with a protective

earth terminal.

• Do not use an extension cord without protective earth ground. Otherwise, the

protection function will be compromised.

Connection Procedure

1.

Check that the power switch on the front panel is OFF.

2.

Connect the power cord plug to the power connector on the rear panel. (Use the

power cord that came with the package.)

3.

Connect the plug on the other end of the power cord to the outlet that meets the

conditions below. The AC outlet must be of a three-pin type with a protective earth

ground terminal.

Item

Specifications

Rated supply voltage*

100 to 120 VAC, 200 to 240 VAC

Permitted supply voltage range

90 to 132 VAC, 180 to 264 VAC

Rated supply voltage frequency

50/60 Hz

Permitted supply voltage frequency range

48 to 63Hz

Maximum power consumption (when using the printer)

250 VA

*

The TA720 can use a 100-V or a 200-V system for the power supply. The maximum rated
voltage of the power cord varies depending on its type. Check that the voltage supplied to
the TA720 is less than or equal to the maximum rated voltage of the provided power cord
(see page ii) before using it.

Power cord
(included in the package)

3-pin outlet

«
...
51
52
53
54
55
...
»

Summary of Contents for TA720





































































































































































































































Reviews:

No comments

Related manuals for TA720

Brand: Labom Pages: 5

Brand: Aaronia Pages: 47

Brand: DAKOTA ULTRASONICS Pages: 48

Brand: TE Connectivity Pages: 9

Brand: Xylem Pages: 24

Brand: Oldham Pages: 22

Brand: bentrup Pages: 9

Brand: Mic Pages: 2

Brand: Autometers Systems Pages: 16

Brand: Omega Pages: 20

Brand: Kawai Pages: 72

Brand: Dakota Digital Pages: 38

Brand: Swema Pages: 4

Brand: LaMotte Pages: 2

Retinomax K+Screeen

Brand: Righton Pages: 112

TWIN LASER GB II

Brand: Nicols Pages: 22

Brand: IFM Pages: 45

Brand: Vaisala Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands