manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, User Manual

The Xilinx Virtex-5 FPGA ML561 offers outstanding performance and versatility for advanced electronic designs. For convenient usage, a comprehensive User Manual is available for free download at manualshive.com. This manual provides detailed instructions and valuable insights, ensuring seamless integration and successful implementation of this cutting-edge product.

Share
Download
background image

54

www.xilinx.com

Virtex-5 FPGA User Guide

UG190 (v5.0) June 19, 2009

Chapter 2:

Clock Management Technology

Phase-Shift Enable Input - PSEN

The phase-shift enable (PSEN) input signal must be synchronous with PSCLK. A variable 
phase-shift operation is initiated by the PSEN input signal. It must be activated for one 
period of PSCLK. After PSEN is initiated, the phase change is gradual with completion 
indicated by a High pulse on PSDONE. There are no sporadic changes or glitches on any 
output during the phase transition. From the time PSEN is enabled until PSDONE is 
flagged, the DCM output clock moves bit-by-bit from its original phase shift to the target 
phase shift. The phase shift is complete when PSDONE is flagged. PSEN must be tied to 
ground when the CLKOUT_PHASE_SHIFT attribute is set to NONE or FIXED. 

Figure 2-6

 

shows the timing for this input.

Dynamic Reconfiguration Data Input - DI[15:0]

The dynamic reconfiguration data (DI) input bus provides reconfiguration data for 
dynamic reconfiguration. When not used, all bits must be assigned zeros. See the Dynamic 
Reconfiguration chapter of the 

Virtex-5 FPGA Configuration Guide

 for more information. 

Dynamic Reconfiguration Address Input - DADDR[6:0]

The dynamic reconfiguration address (DADDR) input bus provides a reconfiguration 
address for the dynamic reconfiguration. When not used, all bits must be assigned zeros 
and the DO output bus reflects the DCM’s status. See the Dynamic Reconfiguration 
chapter of the 

Virtex-5 FPGA Configuration Guide

 for more information. 

Dynamic Reconfiguration Write Enable Input - DWE

The dynamic reconfiguration write enable (DWE) input pin provides the write enable 
control signal to write the DI data into the DADDR address. When not used, it must be tied 
Low. See the Dynamic Reconfiguration chapter of the 

Virtex-5 FPGA Configuration Guide

 for 

more information.

Dynamic Reconfiguration Enable Input - DEN

The dynamic reconfiguration enable (DEN) input pin provides the enable control signal to 
access the dynamic reconfiguration feature. When the dynamic reconfiguration feature is 
not used, DEN must be tied Low. When DEN is tied Low, DO reflects the DCM status 
signals. See the Dynamic Reconfiguration chapter of the 

Virtex-5 FPGA Configuration Guide

 

for more information.

DCM Clock Output Ports

A DCM provides nine clock outputs with specific frequency and phase relationships. 
When CLKFB is connected, all DCM clock outputs have a fixed phase relationship to 
CLKIN. When CLKFB is not connected, the DCM outputs are not phase aligned. However, 
the phase relationship between all output clocks is preserved.

1x Output Clock - CLK0

The CLK0 output clock provides a clock with the same frequency as the DCM’s effective 
CLKIN frequency. By default, the effective input clock frequency is equal to the CLKIN 
frequency. Set the CLKIN_DIVIDE_BY_2 attribute to TRUE to make the effective CLKIN 
frequency ½ the actual CLKIN frequency. The 

CLKIN_DIVIDE_BY_2 Attribute

 description 

provides further information. When CLKFB is connected, CLK0 is phase aligned to 
CLKIN. 

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Virtex-5 FPGA ML561

EAW MX250 Owner'S Manual preview
MX250
Brand: EAW Pages: 10
XESS XStend XS40 User Manual preview
XStend XS40
Brand: XESS Pages: 23
Jetter JetWeb JX2-PR0FI1 Operator'S Manual preview
JetWeb JX2-PR0FI1
Brand: Jetter Pages: 67
Usr USR4504 Installation Manual preview
USR4504
Brand: Usr Pages: 2
Balluff BIC 1I12-P2A25-M30MI1-BPX05-110 User Manual preview
BIC 1I12-P2A25-M30MI1-BPX05-110
Brand: Balluff Pages: 12
Waves MaxxBCL Manual preview
MaxxBCL
Brand: Waves Pages: 41
UfiSpace S9600-64X Hardware Installation Manual preview
S9600-64X
Brand: UfiSpace Pages: 35
Point of View SmartTV 210 User Manual preview
SmartTV 210
Brand: Point of View Pages: 13
Danville Signal Processing dspstak 21262sx User Manual preview
dspstak 21262sx
Brand: Danville Signal Processing Pages: 35
A4Tech RH-10 User Manual preview
RH-10
Brand: A4Tech Pages: 8
Arbor Technology Em104P-i2904 Quick Installation Manual preview
Em104P-i2904
Brand: Arbor Technology Pages: 8
Zigen IP-Logic ZIG-IPPRO-RX Quick Start Manual preview
IP-Logic ZIG-IPPRO-RX
Brand: Zigen Pages: 4
Xyclop XC-16CH-NVR-4TB Quick Start Manual preview
XC-16CH-NVR-4TB
Brand: Xyclop Pages: 19
Patton electronics 593/45 User Manual preview
593/45
Brand: Patton electronics Pages: 8
LevelOne WBA-4000 User Manual preview
WBA-4000
Brand: LevelOne Pages: 49
Amphenol C2LINX Series Installation Manual preview
C2LINX Series
Brand: Amphenol Pages: 43
NEC N8154-25 User Manual preview
N8154-25
Brand: NEC Pages: 47
Renesas H8S/2615 Series User Manual preview
H8S/2615 Series
Brand: Renesas Pages: 28

Brands by name

Popular brands

Load more brands