Xilinx Virtex-5 FPGA ML561 User Manual Download

Page: 306 / 385

306

www.xilinx.com

Virtex-5 FPGA User Guide

UG190 (v5.0) June 19, 2009

Chapter 6:

SelectIO Resources

Nominal PCB Specifications

The nominal SSO table (

Table 6-40

) contains SSO limits for cases where the PCB

parameters meet the following requirements.

Note:

In cases where PCB parameters do not meet all requirements listed below, the Virtex-5 FPGA

SSO Calculator

must

be used to determine the SSO limit, according to the physical factors of the

unique PCB.

PCB Construction

•

CCO

and GND vias should have a drill diameter no less than 11 mils (279 µ).

•

Total board thickness must be no greater than 62 mils (1575 µ).

Signal Return Current Management

•

Traces must be referenced to a plane on an adjacent PCB layer.

•

The reference plane must be either GND or the V

CCO

associated with the output

driver.

•

The reference layer must remain uninterrupted for its full length from device to
device.

Load Traces

•

All IOB output buffers must drive controlled impedance traces with characteristic
impedance of 50

Ω ±

10%.

•

Total capacitive loading at the far end of the trace (input capacitance of receiving
device) must be no more than 10 pF.

Power Distribution System Design

•

Designed according to the

Virtex-5 FPGA PCB Designer’s Guide

♦

Decoupling capacitors per the device guideline

♦

Approved solder land patterns

•

CCO

and GND planes cannot be separated by more than 5.0 mils (152 µ)

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Search results

Summary of Contents for Virtex-5 FPGA ML561

Reviews:

Related manuals for Virtex-5 FPGA ML561

Brands by name

Popular brands

Xilinx Virtex-5 FPGA ML561, User Manual

Search results

Summary of Contents for Virtex-5 FPGA ML561

Reviews:

Related manuals for Virtex-5 FPGA ML561

Brands by name

Popular brands