manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, User Manual

Share
Download
Xilinx Virtex-5 FPGA ML561 User Manual Download Page 119

Virtex-5 FPGA User Guide

www.xilinx.com

119

UG190 (v5.0) June 19, 2009

Synchronous Dual-Port and Single-Port RAMs

Conflict Avoidance

Virtex-5 FPGA block RAM memory is a true dual-port RAM where both ports can access 
any memory location at any time. When accessing the same memory location from both 
ports, the user must, however, observe certain restrictions. There are two fundamentally 
different situations: The two ports either have a common clock (synchronous clocking), or 
the clock frequency and phase is different for the two ports (asynchronous clocking).

Asynchronous Clocking

Asynchronous clocking is the more general case, where the active edges of both clocks do 
not occur simultaneously:

•

There are no timing constraints when both ports perform a read operation.

•

When one port performs a write operation, the other port must not read- or write-
access the same memory location. The simulation model will produce an error if this 
condition is violated. If this restriction is ignored, a read or write operation will 
produce unpredictable results. There is, however, no risk of physical damage to the 
device. If a read and write operation is performed, then the write will store valid data 
at the write location.

Synchronous Clocking

Synchronous clocking is the special case, where the active edges of both port clocks occur 
simultaneously:

•

There are no timing constraints when both ports perform a read operation.

•

When one port performs a write operation, the other port must not write into the 
same location, unless both ports write identical data.

•

When one port performs a write operation, the write operation succeeds; the other 
port can reliably read data from the same location if the write port is in READ_FIRST 
mode. DATA_OUT on both ports will then reflect the previously stored data. 

If the write port is in either WRITE_FIRST or in NO_CHANGE mode, then the DATA-
OUT on the read port would become invalid (unreliable). The mode setting of the 
read-port does not affect this operation.

X-Ref Target - Figure 4-4

Figure 4-4:

NO_CHANGE Mode Waveforms

CLK

WE

DI

ADDR

DO

EN

Disable

Read

XXXX

1111

2222

XXXX

aa

bb

cc

dd

0000

MEM(aa)

MEM(dd)

Read

Write

MEM(bb)=1111

Write

MEM(cc)=2222

ug190_4_05_032206

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands