Xilinx Virtex-5 FPGA ML561 Page 153 User Manual Download

Page: 153 / 385

Virtex-5 FPGA User Guide

www.xilinx.com

153

UG190 (v5.0) June 19, 2009

FIFO Timing Models and Parameters

Clock Event 1: Write Operation and Assertion of Almost FULL Signal

During a write operation to an almost full FIFO, the Almost FULL signal is asserted.

•

At time T

FDCK_DI

, before clock event 1 (WRCLK), data 00 becomes valid at the DI

inputs of the FIFO.

•

At time T

FCCK_WREN

, before clock event 1 (WRCLK), write enable becomes valid at

the WREN input of the FIFO.

•

At time T

FCKO_AFULL

, one clock cycle after clock event 1 (WRCLK), Almost Full is

asserted at the AFULL output pin of the FIFO.

Clock Event 2: Write Operation, and Assertion of FULL Signal

The FULL signal pin is asserted when the FIFO is full.

•

At time T

FDCK_DI

, before clock event 2 (WRCLK), data 04 becomes valid at the DI

inputs of the FIFO.

•

Write enable remains asserted at the WREN input of the FIFO.

•

At time T

FCKO_FULL

, after clock event 2 (WRCLK), Full is asserted at the FULL output

pin of the FIFO.

If the FIFO is full, and a read followed by a write is performed, the FULL signal remains
asserted.

Clock Event 3: Write Operation and Assertion of Write Error Signal

The write error signal pin is asserted when data going into the FIFO is not written because
the FIFO is in a Full state.

•

At time T

FDCK_DI

, before clock event 3 (WRCLK), data 05 becomes valid at the DI

inputs of the FIFO.

•

Write enable remains asserted at the WREN input of the FIFO.

•

At time T

FCKO_WRERR

, after clock event 3 (WRCLK), a write error is asserted at the

WRERR output pin of the FIFO. Data 05 is not written into the FIFO.

Clock Event 4: Write Operation and Deassertion of Write Error Signal

The write error signal pin is deasserted when a user stops trying to write into a full FIFO.

•

At time T

FCCK_WREN

, before clock event 4 (WRCLK), write enable is deasserted at the

WREN input of the FIFO.

•

At time T

FCKO_WRERR

, after clock event 4 (WRCLK), write error is deasserted at the

WRERR output pin of the FIFO.

The write error signal is asserted/deasserted at every write-clock positive edge. As long as
both the write enable and Full signals are true, write error will remain asserted.

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Search results

Summary of Contents for Virtex-5 FPGA ML561

Reviews:

Related manuals for Virtex-5 FPGA ML561

Brands by name

Popular brands

Xilinx Virtex-5 FPGA ML561, User Manual

Search results

Summary of Contents for Virtex-5 FPGA ML561

Reviews:

Related manuals for Virtex-5 FPGA ML561

Brands by name

Popular brands