manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, User Manual

The Xilinx Virtex-5 FPGA ML561 offers outstanding performance and versatility for advanced electronic designs. For convenient usage, a comprehensive User Manual is available for free download at manualshive.com. This manual provides detailed instructions and valuable insights, ensuring seamless integration and successful implementation of this cutting-edge product.

Share
Download
background image

Virtex-5 FPGA User Guide

www.xilinx.com

53

UG190 (v5.0) June 19, 2009

DCM Ports

Dynamic Reconfiguration Clock Input - DCLK

The dynamic reconfiguration clock (DCLK) input pin provides the source clock for the 
DCM's dynamic reconfiguration circuit. The frequency of DCLK can be asynchronous (in 
phase and frequency) to CLKIN. The dynamic reconfiguration clock signal is driven by 
any clock source (external or internal), including:

1.

IBUF – Input Buffer

2.

IBUFG – Global Clock Input Buffer 

Only the IBUFGs on the same half of the device (top or bottom) as the DCM can be 
used to drive a CLKIN input of the DCM.

3.

BUFGCTRL  – An Internal Global Buffer 

4.

Internal Clock – Any internal clock using general purpose routing.

The frequency range of DCLK is described in the 

Virtex-5 FPGA Data Sheet

. When dynamic 

reconfiguration is not used, this input must be tied to ground. See the dynamic 
reconfiguration chapter in the 

Virtex-5 FPGA Configuration Guide

 for more information.

DCM Control and Data Input Ports

Reset Input - RST

The reset (RST) input pin resets the DCM circuitry. The RST signal is an active High 
asynchronous reset. Asserting the RST signal asynchronously forces all DCM outputs Low 
(the LOCKED signal, all status signals, and all output clocks) after some propagation delay. 
When the reset is asserted, the last cycle of the clocks can exhibit a short pulse and a 
severely distorted duty cycle, or no longer be deskewed with respect to one another while 
asserting High. Deasserting the RST signal starts the locking process at the next CLKIN 
cycle.

To ensure a proper DCM reset and locking process, the RST signal must be held until the 
CLKIN signal is present and stable for at least three CLKIN cycles.

The time it takes for the DCM to lock after a reset is specified in the 

Virtex-5 FPGA Data 

Sheet

 

as LOCK_DLL (for a DLL output) and LOCK_FX (for a DFS output). These are the 

CLK and CLKFX outputs described in 

“DCM Clock Output Ports.”

 The DCM locks faster 

at higher frequencies. The worse-case numbers are specified in the 

Virtex-5 FPGA Data 

Sheet

. In all designs, the DCM must be held in reset until CLKIN is stable. 

Phase-Shift Increment/Decrement Input - PSINCDEC

The phase-shift increment/decrement (PSINCDEC) input signal must be synchronous 
with PSCLK. The PSINCDEC input signal is used to increment or decrement the phase-
shift factor when PSEN is activated. As a result, the output clocks are shifted. The 
PSINCDEC signal is asserted High for increment or deasserted Low for decrement. This 
input must be tied to ground when the CLKOUT_PHASE_SHIFT attribute is set to NONE 
or FIXED. 

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Virtex-5 FPGA ML561

CAME QBEMFSB2 User Manual preview
QBEMFSB2
Brand: CAME Pages: 19
Dave Embedded Systems ARM Cortex-A9 MPCore Quick Start Manual preview
ARM Cortex-A9 MPCore
Brand: Dave Embedded Systems Pages: 67
Laurell WS-650 lite Series Operation Manual preview
WS-650 lite Series
Brand: Laurell Pages: 84
Intel F-Tile SDI II Intel Agilex User Manual preview
F-Tile SDI II Intel Agilex
Brand: Intel Pages: 39
Uctronics U6180 Instruction Manual preview
U6180
Brand: Uctronics Pages: 2
Areca ARC-12x4 Series Quick Installation Manual preview
ARC-12x4 Series
Brand: Areca Pages: 2
ekwb 3831109810316 User Manual preview
3831109810316
Brand: ekwb Pages: 16
Zhone 891630 System Reference Manual preview
891630
Brand: Zhone Pages: 494
Renesas Dummy IC M3T-SSOP36B-450 User Manual preview
Dummy IC M3T-SSOP36B-450
Brand: Renesas Pages: 4
Stepper Motor Canada DB25-1R5AM Manual preview
DB25-1R5AM
Brand: Stepper Motor Canada Pages: 7
Alcatel-Lucent 1677 Brochure preview
1677
Brand: Alcatel-Lucent Pages: 8
Aprotech INTEL CORE i5 SYSTEM BOARD User Manual preview
INTEL CORE i5 SYSTEM BOARD
Brand: Aprotech Pages: 154
KTI Networks KGS-2421 User Manual preview
KGS-2421
Brand: KTI Networks Pages: 147
Huawei VCN520 Quick Start Manual preview
VCN520
Brand: Huawei Pages: 15
Huawei V100R012 User Manual preview
V100R012
Brand: Huawei Pages: 20
Huawei ViewPoint 8650 V100R008 Quick Start Manual preview
ViewPoint 8650 V100R008
Brand: Huawei Pages: 36
Huawei V100R003C00 Product Description preview
V100R003C00
Brand: Huawei Pages: 15
Huawei SMUC Specifications preview
SMUC
Brand: Huawei Pages: 2

Brands by name

Popular brands

Load more brands