Xilinx Virtex-5 FPGA ML561 User Manual Download

Page: 168 / 385

168

www.xilinx.com

Virtex-5 FPGA User Guide

UG190 (v5.0) June 19, 2009

Chapter 4:

Block RAM

ECC Timing Characteristics

The various ECC timing parameters are also shown in

Figure 4-31

and

Figure 4-32

Since write clock and read clock are independent of each other, all write timing in

Figure 4-31

is referenced to WRCLK. All read timing in

Figure 4-32

is referenced to

RDCLK.

Standard ECC Write Timing (

Figure 4-31

)

•

At time TRCCK_EN, before time T1W, write enable becomes valid at the WREN input
of the block RAM.

•

At time TRCCK_ADDR, before time T1W, write address

becomes valid at the

WRADDR[8:0] inputs of the block RAM. WRADDR input is not needed for FIFO.

•

At time TRDCK_DI_ECC (standard ECC), before time T1W, write data A (hex)
becomes valid at the DI[63:0] inputs of the block RAM.

•

At time TRCKO_ECC_PARITY (standard ECC), after time T1W, ECC parity data PA
(hex) becomes valid at the ECCPARITY[7:0] output pins of the block RAM.

Standard ECC Read Timing (

Figure 4-32

)

•

At time TRCCK_EN, before time T1R, read enable becomes valid at the RDEN input
of the block RAM.

•

At time TRCCK_ADDR, before time T1R, write address

becomes valid at the

RDADDR[8:0] inputs of the block RAM. RDADDR input is not needed for FIFO.

DO_REG = 0

♦

At time TRCKO_DO (latch mode), after time T1R, data A (hex) becomes valid at
the DO[63:0] output pins of the block RAM.

♦

At time TRCKO_DOP (latch mode), after time T1R, data PA (hex) becomes valid
at the DOP[7:0] output pins of the block RAM.

♦

At time TRCKO_ECC_SBITERR (latch mode), after time T1R, SBITERR is asserted
if single-bit error is detected and corrected on data set A.

♦

At time TRCKO_ECC_DBITERR (latch mode), after time T2R, DBITERR is
asserted if double-bit error is detected on data set B.

DO_REG = 1

♦

At time TRCKO_DO (register mode), after time T2R, data A (hex) becomes valid
at the DO[63:0] output pins of the block RAM.

♦

At time TRCKO_DOP (register mode), after time T2R, data PA (hex) becomes
valid at the DOP[7:0] output pins of the block RAM.

♦

At time TRCKO_ECCR_SBITERR (register mode), after time T2R, SBITERR is
asserted if single-bit error is detected and corrected on data set A.

♦

At time TRCKO_ECCR_DBITERR (register mode), after time T3R, DBITERR is
asserted if double-bit error is detected on data set B.

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Search results

Summary of Contents for Virtex-5 FPGA ML561

Reviews:

Related manuals for Virtex-5 FPGA ML561

Brands by name

Popular brands

Xilinx Virtex-5 FPGA ML561, User Manual

Search results

Summary of Contents for Virtex-5 FPGA ML561

Reviews:

Related manuals for Virtex-5 FPGA ML561

Brands by name

Popular brands