manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, User Manual

Share
Download
Xilinx Virtex-5 FPGA ML561 User Manual Download Page 117

Virtex-5 FPGA User Guide

www.xilinx.com

117

UG190 (v5.0) June 19, 2009

Synchronous Dual-Port and Single-Port RAMs

Read Operation

In latch mode, the read operation uses one clock edge. The read address is registered on the 
read port, and the stored data is loaded into the output latches after the RAM access time. 
When using the output register, the read operation will take one extra latency cycle.

Write Operation

A write operation is a single clock-edge operation. The write address is registered on the 
write port, and the data input is stored in memory.

Write Modes

Three settings of the write mode determines the behavior of the data available on the 
output latches after a write clock edge: WRITE_FIRST, READ_FIRST, and NO_CHANGE. 
Write mode selection is set by configuration. The Write mode attribute can be individually 
selected for each port. The default mode is WRITE_FIRST. WRITE_FIRST outputs the 
newly written data onto the output bus. READ_FIRST outputs the previously stored data 
while new data is being written. NO_CHANGE maintains the output previously 
generated by a read operation.

For the simple dual port block RAM and ECC configurations, the Write mode is always 
READ_FIRST, and therefore no collision can occur when used in synchronous mode.

CASCADEOUTLAT[A|B]

Cascade output pin for 64K x 1 mode when optional output 
registers are not enabled

CASCADEINREG[A|B]

Cascade input for 64K x 1 mode when optional input register 
is enabled

CASCADEOUTREG[A|B]

Cascade output for 64K x 1 mode when optional output 
register is enabled

Notes: 

1. The 

“Data-In Buses - DI[A|B]<#:0> & DIP[A|B]<#:0>”

 section has more information on data parity 

pins.

Table 4-2:

True Dual-Port Names and Descriptions 

(Continued)

Port Name

Description

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands