Xilinx Virtex-5 FPGA ML561 User Manual Download | Manualshive

Page: 209 / 385

background image

Virtex-5 FPGA User Guide

209

UG190 (v5.0) June 19, 2009

CLB / Slice Timing Models

Clock Event 1: Shift In

During a write (Shift In) operation, the single-bit content of the register at the address on
the A/B/C/D inputs is changed, as data is shifted through the SRL. The data written to
this register is reflected on the A/B/C/D outputs synchronously, if the address is
unchanged during the clock event. If the A/B/C/D inputs are changed during a clock
event, the value of the data at the addressable output (A/B/C/D outputs) is invalid.

•

At time T

WS

before clock event 1, the write-enable signal (WE) becomes valid-High,

enabling the SRL for the Write operation that follows.

•

At time T

DS

before clock event 1 the data becomes valid (0) at the DI input of the SRL

and is reflected on the A/B/C/D output after a delay of length T

REG

after clock event

1. Since the address 0 is specified at clock event 1, the data on the DI input is reflected
at A/B/C/D output, because it is written to register 0.

Clock Event 2: Shift In

•

At time T

DS

before clock event 2, the data becomes valid (1) at the DI input of the SRL

and is reflected on the A/B/C/D output after a delay of length T

REG

after clock event

2. Since the address 0 is still specified at clock event 2, the data on the DI input is
reflected at the D output, because it is written to register 0.

Clock Event 3: Shift In/Addressable (Asynchronous) READ

All Read operations are asynchronous to the CLK signal. If the address is changed
(between clock events), the contents of the register at that address are reflected at the
addressable output (A/B/C/D outputs) after a delay of length T

ILO

(propagation delay

through a LUT).

•

At time T

DS

before clock event 3, the data becomes valid (1) at the DI input of the SRL

and is reflected on the A/B/C/D output T

REG

time after clock event 3.

•

The address is changed (from 0 to 2). The value stored in register 2 at this time is a 0
(in this example, this was the first data shifted in), and it is reflected on the A/B/C/D
output after a delay of length T

ILO

.

Clock Event 32: MSB (Most Significant Bit) Changes

At time T

REG

after clock event 32, the first bit shifted into the SRL becomes valid (logical 0

in this case) on the DMUX output of the slice via the MC31 output of LUT A (SRL). This is
also applicable to the AMUX, BMUX, CMUX, DMUX, and COUT outputs at time T

REG

and

T

WOSCO

after clock event 1.

«
...
207
208
209
210
211
...
»

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Virtex-5 FPGA ML561

Brand: ICP DAS USA Pages: 48

Brand: ICP DAS USA Pages: 24

Brand: Compaq Pages: 112

Brand: Black Box Pages: 9

Brand: Waves Pages: 41

AAA-130SA SERIES

Brand: Adaptec Pages: 94

EK-FC980 GTX Classy

Brand: ekwb Pages: 2

Brand: ETAS Pages: 84

Brand: Kaya Instruments Pages: 48

Masterliquid ML240L RGB

Brand: Cooler Master Pages: 18

AirStation G54 WLA2-G54

Brand: Buffalo Pages: 8

Brand: Intel Pages: 51

Brand: Cutting Edge Pages: 92

Internet Security Appliances

Brand: SonicWALL Pages: 293

Brand: Jabra Pages: 2

Brand: Vivotek Pages: 185

Brand: Arduino Pages: 10

Brand: Extron electronics Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands