manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, User Manual

The Xilinx Virtex-5 FPGA ML561 offers outstanding performance and versatility for advanced electronic designs. For convenient usage, a comprehensive User Manual is available for free download at manualshive.com. This manual provides detailed instructions and valuable insights, ensuring seamless integration and successful implementation of this cutting-edge product.

Share
Download
background image

346

www.xilinx.com

Virtex-5 FPGA User Guide

UG190 (v5.0) June 19, 2009

Chapter 7:

SelectIO Logic Resources

The SAME_EDGE mode is the same as for the Virtex-4 architecture. This mode allows 
designers to present both data inputs to the ODDR primitive on the rising-edge of the 
ODDR clock, saving CLB and clock resources, and increasing performance. This mode is 
implemented using the DDR_CLK_EDGE attribute. It is supported for 3-state control as 
well. The following sections describe each of the modes in detail.

OPPOSITE_EDGE Mode

In OPPOSITE_EDGE mode, both the edges of the clock (CLK) are used to capture the data 
from the FPGA fabric at twice the throughput. This structure is similar to the Virtex-II 
Virtex-II Pro, and Virtex-4 FPGA implementation. Both outputs are presented to the data 
input or 3-state control input of the IOB. The timing diagram of the output DDR using the 
OPPOSITE_EDGE mode is shown in 

Figure 7-23

.

SAME_EDGE Mode

In SAME_EDGE mode, data can be presented to the IOB on the same clock edge. 
Presenting the data to the IOB on the same clock edge avoids setup time violations and 
allows the user to perform higher DDR frequency with minimal register to register delay, 
as opposed to using the CLB registers. 

Figure 7-24

 shows the timing diagram of the output 

DDR using the SAME_EDGE mode.

X-Ref Target - Figure 7-23

Figure 7-23:

Output DDR Timing in OPPOSITE_EDGE Mode

ug190_7_18_041206

CLK

OCE

OQ

D1

D2

D1A

D2A

D1B

D1A

D1B

D1C

D1D

D2A

D2B

D2C

D2D

D2B D1C D2C D1D

X-Ref Target - Figure 7-24

Figure 7-24:

Output DDR Timing in SAME_EDGE Mode

ug190_7_19_041206

CLK

OCE

OQ

D1

D2

D1A

D2A

D1B

D1A

D1B

D1C

D1D

D2A

D2B

D2C

D2D

D2B D1C D2C D1D

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Virtex-5 FPGA ML561

D-Link DXS-3610-54S Quick Installation Manual preview
DXS-3610-54S
Brand: D-Link Pages: 38
D-Link Web Smart DES-1210-28P Selection Manual preview
Web Smart DES-1210-28P
Brand: D-Link Pages: 6
D-Link xStack Storage DSN-4000 Series Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 23
D-Link Express EtherNetwork DI-604 Brochure preview
Express EtherNetwork DI-604
Brand: D-Link Pages: 7
D-Link xStack Storage DSN-4000 Series Cli User'S Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 97
NEC Express5800/E120d-M Getting Started preview
Express5800/E120d-M
Brand: NEC Pages: 2
Automationdirect.com CLICK PLUS C2-02CPU Quick Start Manual preview
CLICK PLUS C2-02CPU
Brand: Automationdirect.com Pages: 10
Hama FireWire Combo Instructions Manual preview
FireWire Combo
Brand: Hama Pages: 8
Lanner NCA-4035 User Manual preview
NCA-4035
Brand: Lanner Pages: 109
ADC PG-FlexPlus AMU-912 Manual preview
PG-FlexPlus AMU-912
Brand: ADC Pages: 130
Fieldbus Specialists AT-FBUS Getting Started preview
AT-FBUS
Brand: Fieldbus Specialists Pages: 39
Keithley PDISO-8 User Manual preview
PDISO-8
Brand: Keithley Pages: 71
Uniflair PCOWeb Instruction Manual preview
PCOWeb
Brand: Uniflair Pages: 24
National Instruments SC-2040 User Manual preview
SC-2040
Brand: National Instruments Pages: 56
ORiNG PCard-E 021L-D5 Series Quick Installation Manual preview
PCard-E 021L-D5 Series
Brand: ORiNG Pages: 2
MA lighting 8Port Node Quick Manual preview
8Port Node
Brand: MA lighting Pages: 49
ATTO Technology iPBridge 2500C Specifications preview
iPBridge 2500C
Brand: ATTO Technology Pages: 2
Lantronix N-FXE 02B Series User Manual preview
N-FXE 02B Series
Brand: Lantronix Pages: 10

Brands by name

Popular brands

Load more brands