manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, User Manual

The Xilinx Virtex-5 FPGA ML561 offers outstanding performance and versatility for advanced electronic designs. For convenient usage, a comprehensive User Manual is available for free download at manualshive.com. This manual provides detailed instructions and valuable insights, ensuring seamless integration and successful implementation of this cutting-edge product.

Share
Download
background image

68

www.xilinx.com

Virtex-5 FPGA User Guide

UG190 (v5.0) June 19, 2009

Chapter 2:

Clock Management Technology

Only when feedback is provided to the CLKFB input of the DCM is the frequency 
synthesizer output phase aligned to the clock output, CLK0.

The internal operation of the frequency synthesizer is complex and beyond the scope of 
this document. As long as the frequency synthesizer is within the range specified in the 

Virtex-5 FPGA Data Sheet

, it multiplies the incoming frequencies by the pre-calculated 

quotient M ÷ D and generates the correct output frequencies.

For example, assume an input frequency of 50 MHz, M = 25, and D = 8 (M and D values do 
not have common factors and cannot be reduced). The output frequency is 156.25 MHz 
although separate calculations, 25 x 50 MHz = 1.25 GHz and 50 MHz ÷ 8 = 6.25 MHz, 
seem to produce separate values outside the range of the input frequency. 

Frequency Synthesizer Characteristics

•

The frequency synthesizer provides an output frequency equal to the input frequency 
multiplied by M and divided by D. 

•

The outputs CLKFX and CLKFX180 always have a 50/50 duty-cycle.

•

Smaller M and D values achieve faster lock times. Whenever possible, divide M and D 
by the largest common factor to get the smallest values. (e.g., if the required 
CLKFX = 9/6 x CLKIN, instead of using M =  9 and D = 6, use M = 3 and D = 2.)

•

When CLKFB is connected, CLKFX is phase aligned with CLK0 every D cycles of 
CLK0 and every M cycles of CLKFX if M/D is a reduced fraction.

Phase Shifting

The DCM provides coarse and fine-grained phase shifting. For coarse-phase control, the 
CLK0, CLK90, CLK180, and CLK270 outputs are each phase-shifted by ¼ of the input clock 
period relative to each other. Similarly, CLK2X180 and CLKFX180 provide a 180° coarse 
phase shift of CLK2X and CLKFX, respectively. The coarse phase-shifted clocks are 
produced from the delay lines of the DLL circuit. The phase relationship of these clocks is 
retained when CLKFB is not connected.

Fine-grained phase shifting uses the CLKOUT_PHASE_SHIFT and PHASE_SHIFT 
attributes to phase-shift DCM output clocks relative to CLKIN. Since the CLKIN is used as 
the reference clock, the feedback (CLKFB) connection is required for the phase-shifting 
circuit to compare the incoming clock with the phase-shifted clock. The rest of this section 
describes fine-grained phase shifting in the Virtex-5 FPGA DCM.

Phase-Shifting Operation

All nine DCM output clocks are adjusted when fine-grained phase shifting is activated. 
The phase shift between the rising edges of CLKIN and CLKFB is a specified fraction of the 
input clock period or a specific amount of DCM_TAP. All other DCM output clocks retain 
their phase relation to CLK0.

Phase-Shift Range

The allowed phase shift between CLKIN and CLKFB is limited by the phase-shift range. 
There are two separate phase-shift ranges: 

•

PHASE_SHIFT attribute range

•

FINE_SHIFT_RANGE DCM timing parameter range

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Virtex-5 FPGA ML561

Falcon 4G COMBO User Manual preview
4G COMBO
Brand: Falcon Pages: 24
Black Box JPM083A Manual preview
JPM083A
Brand: Black Box Pages: 9
ekwb EK-FC Installation Manual preview
EK-FC
Brand: ekwb Pages: 2
Garland EdgeLens INT10G8LR56 User Manual preview
EdgeLens INT10G8LR56
Brand: Garland Pages: 30
Aruba IntroSpect Analyzer 2 Series Quick Start Manual preview
IntroSpect Analyzer 2 Series
Brand: Aruba Pages: 5
Paradyne Hotwire 8775 MSDSL Installation Instructions Manual preview
Hotwire 8775 MSDSL
Brand: Paradyne Pages: 10
Multitech ISI608PC Owner'S Manual preview
ISI608PC
Brand: Multitech Pages: 81
Rainbow QPBB Instruction Manual preview
QPBB
Brand: Rainbow Pages: 2
Intercoax IXWB-450 Quick Start Manual preview
IXWB-450
Brand: Intercoax Pages: 2
Raven RFMOW V2 User Manual preview
RFMOW V2
Brand: Raven Pages: 33
Cooler Master Masterliquid ML240L RGB Manual preview
Masterliquid ML240L RGB
Brand: Cooler Master Pages: 18
DayTronic PC-HSICA Instruction Manual preview
PC-HSICA
Brand: DayTronic Pages: 13
WatchNet ENM-04 POE Quick Connection Manual preview
ENM-04 POE
Brand: WatchNet Pages: 2
Rimage CDPR3 User Manual preview
CDPR3
Brand: Rimage Pages: 30
IBM 32R1860 - Nortel Layer 2/3 Copper GbE Switch... User Manual preview
32R1860 - Nortel Layer 2/3 Copper GbE Switch...
Brand: IBM Pages: 14
Magtek IntelliStripe 65 Technical Reference Manual preview
IntelliStripe 65
Brand: Magtek Pages: 44
Jameco JE1049 User Manual preview
JE1049
Brand: Jameco Pages: 13
Ericsson Baseband 6648 Manual preview
Baseband 6648
Brand: Ericsson Pages: 16

Brands by name

Popular brands

Load more brands