manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, User Manual

Share
Download
Xilinx Virtex-5 FPGA ML561 User Manual Download Page 331

Virtex-5 FPGA User Guide

www.xilinx.com

331

UG190 (v5.0) June 19, 2009

Input/Output Delay Element (IODELAY)

Clock Event 1

On the rising edge of C, a reset is detected, causing the output DATAOUT to select tap 0 as 
the output from the 64-tap chain (assuming IDELAY_VALUE = 0).

Clock Event 2

A pulse on CE and INC is captured on the rising edge of C. This indicates an increment 
operation. The output changes without glitches from tap 0 to tap 1. See 

“Stability after an 

Increment/Decrement Operation.”

Clock Event 3

CE and INC are no longer asserted, thus completing the increment operation. The output 
remains at tap 1 indefinitely until there is further activity on the RST, CE, or INC pins.

Stability after an Increment/Decrement Operation

Figure 7-9

 shows a period of instability when the output is changing from one tap to 

another. Clearly, when the data value at tap 0 is different from the data value at tap 1, the 
output must change state. However, when the data values at tap 0 and tap 1 are the same 
(e.g., both 0 or both 1), then the transition from tap 0 to tap 1 causes no glitch or disruption 
on the output. This concept can be comprehended by imagining the receiver data signal in 
the IODELAY tap chain. If tap 0 and tap 1 are both near the center of the receiver data eye, 
then the data sampled at tap 0 should be no different than the data sampled at tap 1. In this 
case, the transition from tap 0 to tap 1 causes no change to the output. To ensure that this is 
the case, the increment/decrement operation of IODELAY is designed to be glitchless.

The user can dynamically adjust the IODELAY tap setting in real-time while live user data 
is passing through the IODELAY element; the adjustments do not disrupt the live user 
data.

The glitchless behavior also applies when an IODELAY element is used in the path of a 
clock signal. Adjusting the tap setting does not cause a glitch or disruption on the output. 
The tap setting of the IODELAY element in the clock path can be adjusted without 
disrupting state machines that could be running on that clock. 

IODELAY VHDL and Verilog Instantiation Template

VHDL and Verilog instantiation templates are available in the Libraries Guide for all 
primitives and submodules.

In VHDL, each template has a component declaration section and an architecture section. 
Each part of the template should be inserted within the VHDL design file. The port map of 
the architecture section should include the design signals names.

Fixed Delay Mode

The Libraries Guide includes templates showing how to instantiate the IODELAY module 
in fixed delay mode with a tap setting of 31. IDELAYCTRL must also be instantiated when 
operating in this mode. See 

“IDELAYCTRL Overview,” page 337

.

Variable Delay Mode 

The Libraries Guide shows how to instantiate the IODELAY module in variable delay 
mode. IDELAYCTRL must also be instantiated when operating in this mode. See 

“IDELAYCTRL Overview,” page 337

.

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands