manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, User Manual

Share
Download
Xilinx Virtex-5 FPGA ML561 User Manual Download Page 323

Virtex-5 FPGA User Guide

www.xilinx.com

323

UG190 (v5.0) June 19, 2009

ILOGIC Resources

Clock Event 4

•

At time T

ISRCK

 before Clock Event 4, the SR signal (configured as synchronous reset in 

this case) becomes valid-High resetting the input register and reflected at the Q1 
output of the IOB at time T

ICKQ

 after Clock Event 4.

ILOGIC Timing Characteristics, DDR

Figure 7-7

 illustrates the ILOGIC in IDDR mode timing characteristics. When IDELAY is 

used, T

IDOCK

 is replaced by T

IDOCKD

. The example shown uses IDDR in 

OPPOSITE_EDGE mode. For other modes, add the appropriate latencies as shown in 

Figure 7-4, page 321

.

Clock Event 1

•

At time T

ICE1CK

 before Clock Event 1, the input clock enable signal becomes valid-

High at the CE1 input of both of the DDR input registers, enabling them for incoming 
data. Since the CE1 and D signals are common to both DDR registers, care must be 
taken to toggle these signals between the rising edges and falling edges of CLK as 
well as meeting the register setup-time relative to both clocks.

•

At time T

IDOCK

 before Clock Event 1 (rising edge of CLK), the input signal becomes 

valid-High at the D input of both registers and is reflected on the Q1 output of input 
register 1 at time T

ICKQ

 after Clock Event 1.

Clock Event 2

•

At time T

IDOCK

 before Clock Event 2 (falling edge of CLK), the input signal becomes 

valid-Low at the D input of both registers and is reflected on the Q2 output of input 
register 2 at time T

ICKQ

 after Clock Event 2 (no change in this case).

Clock Event 9

•

At time T

ISRCK

 before Clock Event 9, the SR signal (configured as synchronous reset in 

this case) becomes valid-High resetting Q1 at time T

ICKQ

 after Clock Event 9, and Q2 

at time T

ICKQ

 after Clock Event 10.

Table 7-5

 describes the function and control signals of the ILOGIC switching characteristics 

in the 

Virtex-5 FPGA Data Sheet

.

X-Ref Target - Figure 7-7

Figure 7-7:

ILOGIC in IDDR Mode Timing Characteristics (OPPOSITE_EDGE Mode)

1

2

3

4

5

6

7

8

9

10

11

T

IDOCK

 

T

ICE1CK 

T

ISRCK 

T

ICKQ

T

ICKQ 

T

ICKQ 

T

IDOCK

 

CLK

D

CE1

SR

(Reset)

Q1

Q2

T

ICKQ 

UG190_7_07_041206

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands