Xilinx MicroBlaze Reference Manual Download Page 28

Page: 28 / 262

www.xilinx.com

MicroBlaze Processor Reference Guide

UG081 (v14.7)

Chapter 2:

MicroBlaze Architecture

Exception Enable
0 = Hardware exceptions disabled

1 = Hardware exceptions enabled

Only available if configured with exception support
(

C_*_EXCEPTION

C_USE_MMU > 0

)

Read/Write

DCE

Data Cache Enable
0 = Data Cache disabled

1 = Data Cache enabled

Only available if configured to use data cache
(

C_USE_DCACHE

= 1)

Read/Write

DZO

Division by Zero or Division Overflow

0 = No division by zero or division overflow has occurred

1 = Division by zero or division overflow has occurred

Only available if configured to use hardware divider
(

C_USE_DIV

= 1)

Read/Write

ICE

Instruction Cache Enable
0 = Instruction Cache disabled

1 = Instruction Cache enabled

Only available if configured to use instruction cache
(

C_USE_ICACHE = 1

)

Read/Write

FSL

Stream (FSL or AXI) Error
0 = get or getd had no error

1 = get or getd control type mismatch
This bit is sticky, i.e. it is set by a get or getd instruction
when a control bit mismatch occurs. To clear it an mts or
msrclr instruction must be used.

Only available if configured to use stream links
(

C_FSL_LINKS > 0

)

Read/Write

BIP

Break in Progress
0 = No Break in Progress

1 = Break in Progress
Break Sources can be software break instruction or hardware
break from

Ext_Brk

Ext_NM_Brk

pin.

Read/Write

Table 2-9:

Machine Status Register (MSR)

(Continued)

Bits

Name

Description

Reset Value

Send Feedback

Summary of Contents for MicroBlaze







































































































































































































































































Search results

Summary of Contents for MicroBlaze

Reviews:

Related manuals for MicroBlaze

Brands by name

Popular brands

Xilinx MicroBlaze, Reference Manual

Search results

Summary of Contents for MicroBlaze

Reviews:

Related manuals for MicroBlaze

Brands by name

Popular brands