Xilinx MicroBlaze Reference Manual Download Page 219 | Manualshive

Page: 219 / 262

background image

MicroBlaze Processor Reference Guide

219

UG081 (v14.7)

Instructions

mts

Move To Special Purpose Register

Description

Copies the contents of register rD into the special purpose register rS. The special purpose registers
TLBLO and TLBHI are used to copy to the Unified TLB entry indexed by TLBX.

When MicroBlaze is configured to use an MMU (

C_USE_MMU

>= 1) this instruction is privileged.

This means that if the instruction is attempted in User Mode (

MSR[UM]

= 1) a Privileged Instruction

exception occurs.

With low-latency interrupt mode (

C_USE_INTERRUPT

= 2), the Interrupt_Ack output port is set to

11 if the MSR{IE] bit is set by executing this instruction.

Pseudocode

if MSR[UM] = 1 then

ESR[EC]

←

00111

else

switch (rS)

case 0x0001 : MSR

←

(rA)

case 0x0007 : FSR

←

(rA)

case 0x0800 : SLR

←

(rA)

case 0x0802 : SHR

←

(rA)

case 0x1000 : PID

←

(rA)

case 0x1001 : ZPR

←

(rA)

case 0x1002 : TLBX

←

(rA)

case 0x1003 : TLBLO

←

(rA)

case 0x1004 : TLBHI

←

(rA)

case 0x1005 : TLBSX

←

(rA)

if (rS) = 0x0001 and (rA) & 2

Interrupt_Ack

←

11

Registers Altered

•

rS

•

ESR[EC], in case a privileged instruction exception is generated

Latency

•

1 cycle

Notes

When writing MSR using MTS, all bits take effect one cycle after the instruction has been executed.
An MTS instruction writing MSR should never be followed back-to-back by an instruction that uses
the MSR content. When clearing the IE bit, it is guaranteed that the processor will not react to any
interrupt for the subsequent instructions. When setting the EIP or BIP bit, it is guaranteed that the
processor will not react to any interrupt or normal hardware break for the subsequent instructions.

mts

rS, rA

1 0 0 1 0 1 0 0 0 0 0

rA

1 1

rS

0

6

11

16

18

31

«
...
217
218
219
220
221
...
»

Summary of Contents for MicroBlaze







































































































































































































































































Reviews:

No comments

Related manuals for MicroBlaze

Brand: TC Electronic Pages: 55

tBOX330-870-FL Series

Brand: AXIOMTEK Pages: 2

Brand: Funkwerk Pages: 2

Brand: Quectel Pages: 23

Brand: Bridgeworks Pages: 18

Brand: M86 Security Pages: 309

Brand: IDT Pages: 207

Compact NVR-AS 4000

Brand: IndigoVision Pages: 38

HHM Series HHM2409

Brand: TDK Pages: 2

Brand: National Instruments Pages: 80

Brand: Advantech Pages: 108

Wisenet XRN-6410RB2-24TB

Brand: Hanwha Techwin Pages: 124

Network Scanning Unit A

Brand: Ricoh Pages: 206

Brand: Lanner Pages: 99

Brand: Arctic Pages: 7

NexXxoS GPX-N 970 M03

Brand: Alphacool Pages: 2

IQ Switch ProxSense RS100

Brand: Azoteq Pages: 9

ROScube-I Series

Brand: ADLINK Technology Pages: 95

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands