![background image](http://html2.mh-extra.com/html/xerox/nuvera-100/nuvera-100_service-manual_3392260085.webp)
Error Codes and Messages
2-7
4,000: PC Processor Control Supervisor (continued)
Error Codes
Front Panel
Display
Software Error Code
Meaning
4,006.45
(0x2406)
PC-DEV_FAULT_300DPI_CAL
pc fault: 300 dpi calib
Calibration Failure: Target Volt-Sec Area of 300
DPI could not be achieved. Check the hardware.
The head may need to be renormalized.
4,007.46
(0x2407)
PC_DEV_FAULT_600DPI_CAL
pc fault: 600 dpi calib
Calibration Failure: Target Volt-Sec Area of 600
DPI could not be achieved. Check the hardware.
The head may need to be renormalized.
4,008.47
(0x2408)
PC_DEV_FAULT_STUCK_DMC
pc fault: DM oil sense
Failure to advance the drum maintenance oiling
mechanism. It has been in the new state for too
long. Check the hardware.
4,009.48
(0x2409)
PC_DEV_FAULT_DM_CAM_BEGIN
pc fault: DM cam start position
At the start of a drum maintenance cycle, when
the DM cam position should have been at blade
down/web down, the DM cam home sensor
should have been TRUE and was instead FALSE.
Check DM cam solenoid, clutch, home sensor,
and related hardware.
4,010.40
(0x240a)
PC_DEV_FAULT_DM_CAM_BU_WU
pc fault: DM cam blade up/web down
During the drum maintenance cycle, when the
DM cam position should have been at blade
up/web up, the DM cam home sensor should
have been FALSE and was instead TRUE. Check
DM cam solenoid, clutch, home sensor, and
related hardware.
4,011.41
(0x240b)
PC_DEV_FAULT_DM_CAM_BU_WD
pc fault: DM cam blade up/web down
During the drum maintenance cycle, when the
DM cam position should have been at blade
up/web down, the DM cam home sensor should
have been FALSE and was instead TRUE. Check
DM cam solenoid, clutch, home sensor, and
related hardware
4,012.42
(0x240c)
PC_DEV_FAULT_DM_CAM_END
pc fault: DM cam end position
At the end of a drum maintenance cycle, when
the DM cam position should have been at blade
down/web down, the DM cam home sensor
should have been TRUE and was instead FALSE.
Check DM cam solenoid, clutch, home sensor,
and related hardware.
4,013.43
(0x240d)
PC_DEV_FAULT_GEAR_GRIND
pc fault: PM disengage
During power-on initialization, the engine is
unable to disengage the process motor. Prior to
declaring this fault, the engine has attempted to
move the process motor through enough
revolutions to disengage the head tilt
mechanism, but the motor stalled somewhere
along the way. The X-axis was then displaced to
the right 0.15 inches and the disengage was
repeated, but the motor stalled again. This leads
to this device fault. The head is unable to move
on the tilt axis, perhaps because it is colliding
with something (head restraint pin, cap, poorly
installed ink loader, screwdriver, etc.).
4,014.44
(0x240e)
PC_DEV_FAULT_6x6DPI_CAL
pc fault: 6x6 dpi calib
Calibration Failure: 600x600 DPI waveform could
not be generated. Check the hardware. The
head may need to be renormalized
Summary of Contents for Nuvera 100
