![background image](http://html2.mh-extra.com/html/xerox/nuvera-100/nuvera-100_service-manual_3392260114.webp)
3-14
ii LINX™ Solid Inkjet 100 Service Manual
Additional Printhead Error Codes:
13,001.40 and 13,0017.47
Open left and right jet stack thermistor. Reseat or
replace the data cable. If the error reoccurs, replace
printhead. If the new printhead gives the same error,
replace the power control board.
13,002.41 and 13,018.48
Jet stack thermistor appears to be shorted. Reseat or
replace the data cable. If the error reoccurs, replace the
printhead. If the new printhead gives same error, replace
the power control board.
13,033.45
The thermistor in the reservoir appears to be open. If the
4-pin connector on the top of the driver board (Figure 3-
9) is disconnected, this error will occur. Turn off the
printer and reseat the cable.
13,034.46
Thermistor appears to be shorted. Look to see if the 4
prong plug on the top of the driver board is plugged in
correctly. If it is, check the data cable. If the data cable is
good, replace printhead. If the error happens on the new
printhead, replace the power control board.
13,035.47 and 13,036.48
Reservoir heater is running away, or reservoir is not
heating. With these errors it is most likely a problem
with the printhead.
12. Check cap/wipe/purge assembly purge performance. After
installing a new printhead, you must recheck the cap/wipe/
purge assembly (Action Steps 4–7). If the printhead is not
installed correctly, the cap/wipe/purge gasket may leak.
NOTE: A broken ink loader can cause the cap/wipe/purge gasket to
not seal. Look for signs of breakage of the black plastic parts on the
underside, especially the bosses that retain the lowest black plastic
panel. Breakage or separation can interfere with head tilt, resulting in
a poor seal with the cap/wipe/purge during the purge process. Replace
the ink loader if broken or defective.
Summary of Contents for Nuvera 100
