![background image](http://html2.mh-extra.com/html/xerox/nuvera-100/nuvera-100_service-manual_3392260004.webp)
1-4
ii LINX™ Solid Inkjet 100 Service Manual
Solid Inkjet 100 Printer Overview
The Solid Inkjet 100 Printer is an Adobe PostScript Level 3 (Version
3010) grayscale, solid inkjet printer. It supports 409 x 409 dots-per-
inch (dpi) resolution at draft mode, and 600 x 600 dpi at High
Resolution Medical mode. The speed of producing images is 4.8 pages-
per-minute (ppm) in draft mode, and 2.5 ppm in High Resolution
Medical mode.
Base Solid Inkjet 100 printer
The base Solid Inkjet 100 printer features 136 built-in fonts, and is
equipped with 64 Mbytes of RAM. It can be upgraded to 128 Mbytes
of RAM by adding an optional 64 Mbyte RAM DIMM.
All printers support two available paper trays: A and A4 trays and an
optional 500-sheet high-capacity paper tray assembly give the printer
a two-tray capability. The high-capacity paper tray assembly is
usually referred to as an auxiliary feeder unit.
A 133-MHz PowerPC processor oversees print engine operations and
PostScript image processing. The printer features an integral
bidirectional parallel port (IEEE 1284C with ECP mode) and a
10baseT Ethernet port (with support for EtherTalk, TCP/IP, DHCP
and Windows Peer-to-Peer). A USB high-speed serial port is also
provided.
An optional Ethernet interface board offers a 10BaseT/100BaseT/
10Base2 Ethernet connection providing standard protocol support for
EtherTalk, TCP/IP and DHCP. When installed, this card disables the
standard 10baseT port.
A second rear panel slot accommodates an internal IDE hard drive for
DICOM support.
Solid inks
Solid inks, sometimes called phase-change inks, are solid at room
temperature and are liquid at the higher temperature used during
printing. The inks solidify almost instantly after being jetted onto the
printer’s drum. Each of the Solid Inkjet 100 printer inks is especially
formulated for this printer; the inks are not interchangeable with
other models of solid ink printers.
NOTE: Turning the printer off and allowing it to cool causes it to
perform a printhead cleaning and purge cycle upon power-up. The
printer’s purge cycle consumes a significant amount of ink. During
normal use and servicing, turn the printer off and allow it to cool only
when necessary.
Summary of Contents for Nuvera 100
