Waters ACQUITY CM-30S Overview And Maintenance Manual Download Page 67

Page: 67 / 146

October 7, 2014, 715004178 Rev. B

Maintaining the 30-cm
single-zone column manager

Keep to a maintenance schedule, and perform maintenance as required

and described in this chapter.

Maintenance schedule

The following table lists periodic maintenance schedules that ensure optimum

performance of the CM-30S.
The maintenance frequencies shown apply to instruments and devices that

normally receive moderate use.

Contents:

Topic

Page

an APC system ........................................................................... 76

Replacing the column-outlet tubing in a CM-30S installed in

a UPC

system............................................................................ 84

Replacing the passive-preheater assembly in a CM-30S

installed in an APC system ....................................................... 97

Replacing the passive-preheater assembly in a CM-30S

installed in a UPC

system ........................................................ 104

Replacing the ferrule on the column fitting.................................... 119
Replacing the valve cartridge.......................................................... 123
Cleaning the exterior of the CM-30S .............................................. 125

Summary of Contents for ACQUITY CM-30S


















































































































































Search results

Summary of Contents for ACQUITY CM-30S

Reviews:

Waters ACQUITY CM-30S, Overview And Maintenance Manual, Page: 67 / 146

Search results

Summary of Contents for ACQUITY CM-30S

Reviews: