Waters ACQUITY CM-30S Overview And Maintenance Manual Download Page 9

Page: 9 / 146

October 7, 2014, 715004178 Rev. B

EMC considerations

Canada spectrum management emissions notice

This class A digital product apparatus complies with Canadian ICES-001.
Cet appareil numérique de la classe A est conforme à la norme NMB-001.

ISM Classification: ISM Group 1 Class B

This classification has been assigned in accordance with IEC CISPR 11

Industrial Scientific and Medical (ISM) instruments requirements. Group 1

products apply to intentionally generated and/or used conductively coupled

radio-frequency energy that is necessary for the internal functioning of the

equipment. Class B products are suitable for use in both commercial and

residential locations and can be directly connected to a low voltage,

power-supply network.

EC authorized representative

Waters Corporation
Stamford Avenue
Altrincham Road
Wilmslow SK9 4AX UK

Telephone:

+44-161-946-2400

Fax:

+44-161-946-2480

Contact:

Quality manager

Summary of Contents for ACQUITY CM-30S


















































































































































Search results

Summary of Contents for ACQUITY CM-30S

Reviews:

Waters ACQUITY CM-30S, Overview And Maintenance Manual, Page: 9 / 146

Search results

Summary of Contents for ACQUITY CM-30S

Reviews: