Waters ACQUITY CM-30S Overview And Maintenance Manual Download Page 43

Page: 43 / 146

Assembling new fittings

October 7, 2014, 715004178 Rev. B

Assembling new fittings

For fitting assemblies that use ferrules not previously assembled or set to

tubing, you must mark the compression screw and fitting body, and ensure

the two marks align when you tighten them.

First use

Stainless steel (gold-plated) fitting with

long flats and 2-piece stainless steel

ferrule

Finger-tight, plus 3/4-turn

using wrench

Reinstal

led

Stainless steel (gold-plated) fitting with

long flats and 2-piece stainless steel

ferrule

Finger-tight, plus up to

1/6-turn using wrench

First use or reinstalled

Dual-threaded, finger-tight fitting with

cap nut

1. Loosen the cap nut from

the dual-threaded,

finger-tight fitting.

2. Finger tighten the

dual-threaded fitting with

the ferrule, into the

column.

3. Tighten the cap nut onto

the dual-threaded,

finger-tight fitting.

Installation recommendations for ACQUITY APC and UPC

column-compartment fittings: (Continued)

Fitting

Recommended tightening

TP03378

Long flats

2-piece ferrule

3/4-turn

TP02713

Long flats

2-piece ferrule

1/6-turn

Dual-threaded
fitting

Ferrule

Cap nut

Summary of Contents for ACQUITY CM-30S


















































































































































Search results

Summary of Contents for ACQUITY CM-30S

Reviews:

Waters ACQUITY CM-30S, Overview And Maintenance Manual, Page: 43 / 146

Search results

Summary of Contents for ACQUITY CM-30S

Reviews: