Waters ACQUITY CM-30S Overview And Maintenance Manual Download Page 42

Page: 42 / 146

2 Preparing and operating the CM-30S

October 7, 2014, 715004178 Rev. B

When tightening system fittings, consult the following table.

Installation recommendations for ACQUITY APC and UPC

column-compartment fittings:

Fitting

Recommended tightening

First use

Stainless steel (gold-plated) fitting with

long flats and 2-piece stainless steel

ferrule on hypo-extended tubing

1. Using your fingers, screw

the gold fitting into the

port and stop as soon as

you begin to feel

resistance (nut is touching

ferrule).

2. Using a 1/4-inch open-end

wrench, tighten until you

begin to feel an increase in

resistance.

3. Using the wrench, tighten

an additional 1/2-turn.

Re-installed

Stainless steel (gold-plated) fitting with

long flats and 2-piece stainless steel

ferrule on hypo-extended tubing

Finger-tight, plus up to

1/6-turn using wrench

TP03493

Long flats

2-piece ferrule

Hypo-extended
tubing

1/2-turn

TP03493

Long flats

2-piece ferrule

Hypo-extended
tubing

1/6-turn

Summary of Contents for ACQUITY CM-30S


















































































































































Search results

Summary of Contents for ACQUITY CM-30S

Reviews:

Waters ACQUITY CM-30S, Overview And Maintenance Manual, Page: 42 / 146

Search results

Summary of Contents for ACQUITY CM-30S

Reviews: