Waters ACQUITY CM-30S Overview And Maintenance Manual Download Page 7

Page: 7 / 146

October 7, 2014, 715004178 Rev. B

vii

Applicable symbols

Symbol

Definition

Manufacturer

Date of manufacture

Authorized representative of the European

Community

Confirms that a manufactured product complies

with all applicable European Community

directives

Australia EMC compliant

Confirms that a manufactured product complies

with all applicable United States and Canadian

safety requirements
Consult instructions for use

Supply ratings

Electrical and electronic equipment with this

symbol may contain hazardous substances and

should not be disposed of as general waste.
For compliance with the Waste Electrical and

Electronic Equipment Directive (WEEE)

2012/19/EU, contact Waters Corporation for the

correct disposal and recycling instructions.
Serial number

Summary of Contents for ACQUITY CM-30S


















































































































































Search results

Summary of Contents for ACQUITY CM-30S

Reviews:

Waters ACQUITY CM-30S, Overview And Maintenance Manual, Page: 7 / 146

Search results

Summary of Contents for ACQUITY CM-30S

Reviews: