Waters ACQUITY CM-30S Overview And Maintenance Manual Download Page 93

Page: 93 / 146

Replacing the column-outlet tubing in a CM-30S installed in a UPC

system

October 7, 2014, 715004178 Rev. B

4. If you are not installing a column on the column-outlet tubing that you

are replacing, route the tubing through a column clip on the column

plate.

Rationale:

Doing so prevents loose tubing from interfering with the

operation of the column-compartment drawer and outer CM-30S door.

5. If you are installing a column on the column-outlet tubing that you are

replacing, do as follows:

a. Ensure the cap nut is loose on the column fitting, insert the

column-outlet tubing into the column, and then tighten the column

fitting.

Column-outlet tubing

Column plate

Column clip

Cap nut

Column fitting

Column

Column-outlet tubing

Summary of Contents for ACQUITY CM-30S


















































































































































Search results

Summary of Contents for ACQUITY CM-30S

Reviews:

Waters ACQUITY CM-30S, Overview And Maintenance Manual, Page: 93 / 146

Search results

Summary of Contents for ACQUITY CM-30S

Reviews: