Viessmann VITODENS 300 WB3A Service Instructions Manual Download Page 104

Page: 104 / 148

Check the sensor resistance and
compare actual values with the
curve.

Replace the sensor in case of
severe deviation.

Danger

The boiler temperature sen-
sor is immersed in the heat-
ing water (risk of scalding).
Drain the boiler before repla-
cing the sensor.

Checking the flue gas temperature sensor

The flue gas temperature sensor locks out the boiler when the permissible flue
gas temperature is exceeded. The lockout can be reset no sooner than after 20
minutes by pressing reset

Note

The equipment will also be locked out again for 20 minutes if the mains power
supply is switched OFF.

Repairs

(cont.)

Troubleshooting

550

Summary of Contents for VITODENS 300 WB3A





















































































































































Search results

Summary of Contents for VITODENS 300 WB3A

Reviews:

Related manuals for VITODENS 300 WB3A

Brands by name

Popular brands

Viessmann VITODENS 300 WB3A, Service Instructions Manual

Search results

Summary of Contents for VITODENS 300 WB3A

Reviews:

Related manuals for VITODENS 300 WB3A

Brands by name

Popular brands