USO
RESTRITO
Names and Functions of Parts of the Control Panel
39
Name
Description
CTR (center)
• Pressing this button once changes the
two-dimensional transformation and
rotation settings to the closest detent
values.
• Pressing the [CTR] button twice, or holding
down [SHIFT] and pressing the [CTR]
button returns the two-dimensional
transformation and rotation settings to the
defaults.
SHIFT
Use this in combination with the [CTR
WORK BUFR] or [CTR] button.
Name
Description
LOC SIZE
(ASP:
aspect)
• Pressing this button and operating the
trackball or Z-ring changes the aspect ratio
of a key to which the resizer function is
applied.
• When this button is held down, the
trackball or Z-ring operation is switched to
a finer control (fine mode).
LOC XYZ
(LOC:
location)
• Pressing this button and operating the
trackball or Z-ring moves, shrinks, or
magnifies a key to which the resizer
function is applied.
• When this button is held down, the
trackball or Z-ring operation is switched to
a finer control (fine mode).
ROT (RSZR:
resizer)
Press this button, turning it on, to enable the
resizer.
ASP PERS
(ROT:
rotation)
• Pressing this button, after pressing the
[RENB] button, and operating the trackball
or Z-ring rotates the key to which the
resizer function is applied or adjusts
perspective.
• When this button is held down, the
trackball or Z-ring operation is switched to
a finer control (fine mode).
AXIS (RENB:
rotation
enable)
Press this button, turning it on, to enable
rotation operation.
CLR WORK
BUFR (clear
work buffer)
• Pressing this button once returns the two-
dimensional transformation and rotation
settings to the defaults.
• Pressing the [CLR WORK BUFR] button
twice, or holding down [SHIFT] and
pressing the [CLR WORK BUFR] button
returns all resizer parameter values to the
defaults.
X, Y, Z
These restrict the axes affected by the
trackball and Z-ring to the X-, Y- or Z-axis.
Ch
a
p
te
r 2
Na
m
e
s
and
Fun
c
ti
o
n
s
of
P
a
rts
When the three-dimensional transform operation
mode is enabled
The buttons are used for three-dimensional DME
transformations.
For details,
“Three-Dimensional Transformation
When the VTR/disk recorder/frame memory
operation mode is enabled
The buttons are used for VTR control or playback of frame
memory clips.
For details,
“Controlling the Tape/Disk Transport”
When the resizer operation mode is enabled
c
Trackball
The effect of operation depends on the operating mode as
follows.
When the positioner operation mode is enabled
By moving this, you can move the pattern in the X-axis and
Y-axis directions.
When the three-dimensional transform operation
mode is enabled
Move the trackball to control three-dimensional transform
operation of the X- and Y-axes.
When the [SRC] or [TRGT] button is held down, the
operation is switched to a finer control (fine mode).
When the resizer operation mode is enabled
By turning the trackball, you can move in the X and Y
directions of the key to which the resizer is applied, change
the aspect ratio, and rotate around the X-axis and Y-axis.
When the [LOC SIZE], [LOC XYZ], or [ASP PERS]
button is held down, the operation is switched to a finer
control (fine mode).
d
Z-ring
The effect of operation depends on the operating mode as
follows.
When the three-dimensional transform operation
mode is enabled
Turn this ring to control three-dimensional transform
operation of the Z-axis.
When the [SRC] or [TRGT] button is held down, the
operation is switched to a finer control (fine mode).
When the keyframe operation mode is enabled
By turning the Z-ring, you can run the keyframe effect,
independent of the STOP NEXT KF, EFFECT LOOP, and
similar settings in the Flexi Pad.
Turn clockwise to run the effect in the normal direction,
and counterclockwise for the reverse direction.
