Solare Datensysteme Solar-Log Components Connection Manual Download Page 348

Page: 348 / 506

348

Steca

92.2

Steca (>=17k)

Termination

Addressing

Interface

Yes

RS485

Select “Steca: USS / >=17kW“ for the device detection.

Overview

•

Integrated interface

•

Where to connect: RJ45 socket on the bottom of the inverter

•

2-pin wiring

•

Communication address must be allocated

•

Installation steps

•

Switch off the inverters and Solar-Log™

•

Connect inverters to the Solar-Log™

•

Connect the inverters to each other

Select the Steca >=17k inverter during the initial configuration.

Note

To use active and reactive power management, all of the inverters need to be set to:

•

Protocol 1

•

57600 baud

•

Parameter 1164 = 2

Connect inverters to the Solar-Log™

The wiring is done using a

•

self-made, shielded 2 wire data cable and terminal block connector.

Procedure

1. Connect wires as shown in the diagram below.

Solar-Log™ terminal strip connector

RS485 inverter socket

Terminal

►

2. If no further inverter connected, terminate the inverter:

On the sockets "RS485 OUT" with SACC-M12MS-4SC round plugs bypass the connections PIN1 to PIN2 and
PIN3 to PIN4.

3. Close the inverter if no other inverters are to be connected.
4. Insert the terminal block connector into the Solar-Log™ RS485 socket.

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Search results

Summary of Contents for Solar-Log

Reviews:

Related manuals for Solar-Log

Brands by name

Popular brands

Solare Datensysteme Solar-Log, Components Connection Manual

Search results

Summary of Contents for Solar-Log

Reviews:

Related manuals for Solar-Log

Brands by name

Popular brands