Solare Datensysteme Solar-Log Components Connection Manual Download | Manualshive

Page: 312 / 506

background image

312

SOCOMEC

85.2

SOCOMEC Sunsys B12/B30

Termination

Addressing

Interface

Yes

Yes

RS485

Selection available under SOCOMEC

Overview

•

Integrated interface

•

Where to connect: RJ45 sockets inside the inverter

•

3-pin wiring

•

The communication address has to be assigned

•

Installation steps

•

Switch off the inverters and Solar-Log™

•

Connect inverters to the Solar-Log™

•

Connect the inverters to each other according to the inverter instructions

•

Communication address according to the inverter‘s instructions
Address range 1 - 255

Connect inverters to the Solar-Log™

The wiring is done using a

•

self-made cable connection with RS485 data cable and terminal block connector.

Procedure

1. Open the inverter according to the inverter‘s instructions.
2. If you are fabricating the cable yourself, connect the wires as shown in the following diagram.

Solar-Log™ terminal strip connector

RJ45 inverter

Terminal

PIN

►

1 Data+

►

5

►

3 GND

►

7

►

4 Data-

►

4

3.  Insert the RJ45 plug into the RJ45 socket on the first inverter.
4.  If no further inverter is connected, terminate the inverter according to the instructions for the inverter.
5.  Close the inverter if no other inverters are to be connected.
6.  Insert the terminal block connector into the Solar-Log™ RS485 socket.

Connect the inverters to each other

•

Connect using a data cable with an RJ45 plug.

•

Where to connect: RJ45 sockets in the inverter.

«
...
310
311
312
313
314
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

Brand: T&D Pages: 2

Brand: Microtronics Pages: 127

Brand: Sharp Pages: 312

Arduino WPSH202

Brand: Whadda Pages: 6

Brand: retmon Pages: 2

Brand: Extech Instruments Pages: 12

Brand: Fluke Pages: 72

Brand: Fluke Pages: 72

Brand: Soil Instruments Pages: 32

Brand: Sper scientific Pages: 36

Brand: M-system Pages: 337

Brand: Spectrum Pages: 12

Brand: Racelogic Pages: 49

Brand: EasyLog Pages: 5

Brand: iGen Pages: 32

Brand: iGen Pages: 2

Brand: SWR SCIENCE Pages: 123

Brand: Velleman Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands