Solare Datensysteme Solar-Log Components Connection Manual Download Page 195

Page: 195 / 506

195

Kstar

Kstar

52.1

Kstar Multitracker

Termination

Addressing

Interface

DIP switch

Yes

RS485

Select “Kstar: KSG TRIO” during the inverter detection

Overview

•

Integrated interface

•

3-pin wiring

•

2 RJ45 sockets on the outside of the inverter

•

Communication address must be allocated

•

Installation steps

•

Switch off the inverters and Solar-Log™

•

Connect inverters to the Solar-Log™

•

Connect the inverters to each other

•

Allocate communication address
Address range 1 to 32
Settings on the inverter’s display according to the manufacturer’s manual

Connect inverters to the Solar-Log™

The wiring is done using a

•

self-made cable connection with RS485 data cable and terminal block connector.

Caution

Risk of damage to the unit!
The Solar-Log™ also has an RJ45 socket, which must never be connected to the RJ45 socket on the
inverter.

►

Only connect inverters via the RS485/422 Solar-Log™ interface(s).

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Search results

Summary of Contents for Solar-Log

Reviews:

Related manuals for Solar-Log

Brands by name

Popular brands

Solare Datensysteme Solar-Log, Components Connection Manual

Search results

Summary of Contents for Solar-Log

Reviews:

Related manuals for Solar-Log

Brands by name

Popular brands