Solare Datensysteme Solar-Log Components Connection Manual Download Page 332 | Manualshive

Page: 332 / 506

background image

332

Solectria

90 Solectria

90.1

Solectria V1 (>9k)

Termination

Addressing

Interface

Yes

Yes

RS485

Selection available under Solectria V1

The following types are to be connected according to this diagram:

•

PVI 10KW

•

PVI 13KW

•

PVI 15KW

•

PVI 100KW

Overview

•

Integrated interface

•

Where to connect: Terminal strip inside the inverter

•

3-pin wiring

•

Communication address must be allocated.

•

Installation steps

•

Switch off the inverters and Solar-Log™

•

Connect inverters to the Solar-Log™

•

Connect the inverters to each other

•

Change the communication address if required.
Every address may only be used once.
Address range 1 to 16.

Connect inverters to the Solar-Log™

The wiring is done using a

•

self-made cable connection with terminal block connector.

•

Where to connect: Terminal strip inside the inverter

Procedure

1. If you are making the cable yourself, connect the wires as shown in the following diagram:

Solar-Log™ terminal strip connector

Terminal strip inside the inverter

Terminal

PIN

►

1 (Data+)

►

RS485 A

►

3 (Ground)

►

RS485 G

►

4 (Data-)

►

RS485 B

2. If no further inverter is connected, terminate the inverter according to the instructions for the inverter.
3. Insert the terminal block connector into the Solar-Log™ RS485 socket.

«
...
330
331
332
333
334
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

Brand: UNI-T Pages: 2

Brand: iGage Pages: 16

Brand: uAvionix Pages: 2

Brand: Microtronics Pages: 145

Brand: Extech Instruments Pages: 7

Brand: Extech Instruments Pages: 11

Brand: Extech Instruments Pages: 10

Brand: Extech Instruments Pages: 11

Brand: Extech Instruments Pages: 15

Brand: ES&S Pages: 13

Logger Patch Amplified

Brand: Total Recall VR Pages: 2

Brand: Santerno Pages: 20

Brand: TempSen Pages: 25

Brand: peoplenet Pages: 15

Brand: Akytec Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands