Solare Datensysteme Solar-Log Components Connection Manual Download Page 267 | Manualshive

Page: 267 / 506

background image

267

Schneider Electric

77.4 Schneider Conext Sunspec (RS485)

Termination

Adressing

Interface

Switch

Yes

RS485

Select “Schneider ElectricConext Sunspec“ for the device detection.

Supported models:

•

CL60

•

CL125

(as of firmware 4.2.0)

Overview

•

Integrated interface

•

Where to connect: RJ45 socket on the outside of the inverter

•

3-pin wiring

•

Communication address must be allocated

•

Installation steps

•

Allocate communication address

•

Switch off the inverters and Solar-Log™

•

Connect inverters to the Solar-Log™

•

Connect the inverters to each other

Connect inverters to the Solar-Log™

The wiring is done using a

•

self-made cable connection with RS485 data cable and terminal block connector.

Procedure

1.  Open the inverter as shown in the inverter‘s instructions.
2.  Insert the RJ45 plug into RJ45-Out socket on the first inverter.
3.  If you are making the cable yourself, connect the wires as shown in the following diagram:

Solar-Log™ terminal strip connector

Inverter RS485

Terminal

Pin

►

1 Data+

►

A+

►

3 GND

►

GND

►

4 Data-

►

B-

4.  If no further inverter is connected, terminate the inverter according to the instructions for the inverter.
5.  Close the inverter if no other inverters are to be connected.
6.  Insert the terminal block connector into the Solar-Log™ RS485 socket.

Caution

Risk of damage to the unit!
The Solar-Log™ also has an RJ45 socket, which must never be connected to the RJ45 socket on the
inverter.

►

Only connect inverters via the RS485/422 Solar-Log™ interface(s).

«
...
265
266
267
268
269
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

Brand: National Instruments Pages: 278

Brand: Lambrecht Pages: 30

Brand: Velleman Pages: 2

Brand: Edaphic Scientific Pages: 19

Brand: Capetti Elettronica Pages: 6

WineCap WSD12T-IIDR

Brand: Capetti Elettronica Pages: 9

Brand: Sper scientific Pages: 36

Brand: T&D Pages: 8

Brand: Senonics Pages: 6

Brand: Senonics Pages: 11

Omniace RA2000 series

Brand: A&D Pages: 114

StowAway-IS Temp

Brand: Onset Computer Corporation Pages: 4

Brand: Auta Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands