Solare Datensysteme Solar-Log Components Connection Manual Download Page 340

Page: 340 / 506

340

Solectria

90.5 Solectria V5

Termination

Adressing

Interface

Jumper

Yes

RS485

Selection under „Solectria V5“

Supported models (as of firmware 4.1.0):

•

PVI 3800 TL

•

PVI 5200 TL

•

PVI 6600 TL

•

PVI 7600 TL

Overview

•

Integrated interface.

•

Where to connect: Terminal block inside the inverter.

•

3-pin wiring.

•

The communication address has to be assigned.

•

Installation steps:

•

Switch off the inverters and the Solar-Log™.

•

Connect the inverters to the Solar-Log™.

•

Connect the inverters to each other.

•

Assign the communication address.
Address range 1 - 254.
Settings on the inverter‘s display according to the manufacturer‘s manual.

Connect the inverters to the Solar-Log™

The wiring is done using a

•

self-made connection cable.

•

Where to connect: Terminal block inside the inverter.

Procedure

1. If you are making the cable yourself, connect the wires as shown in the following diagram:

Solar-Log™ terminal strip connector

Terminal block inside the second inverter (J1)

Terminal

►

1 A/Data+

►

7 TX A (RS485+)

►

3 GND

►

4 GND (RS485)

►

4 B/Data-

►

8 RX B (RS485-)

2. Terminate the inverter if no additional inverters are to be connected:

Set the jumper to „On“ (refer to the inverter‘s instructions).

3. Insert the terminal block connector into the Solar-Log™ RS485 socket.

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Search results

Summary of Contents for Solar-Log

Reviews:

Related manuals for Solar-Log

Brands by name

Popular brands

Solare Datensysteme Solar-Log, Components Connection Manual

Search results

Summary of Contents for Solar-Log

Reviews:

Related manuals for Solar-Log

Brands by name

Popular brands