Solare Datensysteme Solar-Log Components Connection Manual Download | Manualshive

Page: 239 / 506

background image

239

Q3

Note

Each inverter has to be individually reachable via the network. For this, the network interface has to be
activated for every inverter (select "Activate LAN" under the LAN menu) and and the inverter needs to
be connected to the local access network (LAN) via a switch.

Detection via the Solar-Log™ WEB Interface

•

For detection on the Solar-Log™ , select the device class under the menu Configuration | Device | Definition |
Interface with the plus symbol and then select “Q3:QX3“ as the manufacturer. Confirm your selection with OK.

•

Save your selections and then start the Device Detection under Configuration | Device | Detection.

Detection from the Solar-Log 1200

•

When using the Solar-Log 1200, the detection can also be started from the display. Select the settings ►Start

►

Initial Configuration

►

Page 2 „Device“

►

Add and select the manufacturer “Q3:QX3“ from there. Save and

start the Device Detection.

Note for feed-in management

Supported by Solar-Log
starting with inverter firmware version 19

Note

Using the inverter's web interface, select "External control via network interface" under “Settings

►

Installation

►

Grid Company Settings

►

Power Reduction," and under “cos(phi) Settings.”

«
...
237
238
239
240
241
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

Brand: Campbell Pages: 86

Brand: RainWise Pages: 24

PortaSens II C16

Brand: Ozone Solutions Pages: 10

Brand: Casio Pages: 37

BioNomadix Logger

Brand: BIOPAC Systems, Inc. Pages: 28

Onset HOBO UX100-001

Brand: ALAT UJI Pages: 7

Brand: Fluke Pages: 4

COMARK Diligence RF313-TH

Brand: Fluke Pages: 3

Brand: Fluke Pages: 62

Squirrel 2020 Series

Brand: Grant Datalogging Pages: 17

Brand: Dataq Pages: 48

Brand: dataTaker Pages: 29

Brand: Teac Pages: 36

Brand: Lambrecht Pages: 30

Brand: Hi-Target Pages: 192

Brand: SWR SCIENCE Pages: 123

Brand: Eagle Tree Systems Pages: 3

Brand: METER GROUP Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands