Solare Datensysteme Solar-Log Components Connection Manual Download Page 66

Page: 66 / 506

Bonfiglioli (formerly Vectron)

Bonfiglioli (formerly Vectron)

13.1

Bonfiglioli

Termination

Addressing

Interface

DIP switch

Yes

RS485

Overview

•

Integrated interface.

•

Where to connect: Terminal strip inside the inverter.

•

3-pin wiring.

•

Communication address must be allocated.

•

Installation steps:

•

Switch off the inverters and Solar-Log™.

•

Connect inverters to the Solar-Log™.

•

Connect the inverters to each other.

•

Allocate communication address.

Connect inverters to the Solar-Log™

The wiring is done using a

•

self-made, shielded 3 wire data cable with a terminal block connector.

Procedure

1. Get access to the inverter interface.
2. If you are making the cable yourself, connect the wires as shown in the following diagram:

Solar-Log™ terminal strip connector

Terminal strip inside the inverter

Terminal

RS485 terminal

►

1 A (Data+)

►

6 GND

►

3 B (Data-)

3. If no further inverter is connected, terminate the inverter:

In the inverter, set the DIP switch S1 for the terminal resistor to ON.

4. Insert the terminal block connector into the Solar-Log™ RS485 socket.

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Search results

Summary of Contents for Solar-Log

Reviews:

Related manuals for Solar-Log

Brands by name

Popular brands

Solare Datensysteme Solar-Log, Components Connection Manual

Search results

Summary of Contents for Solar-Log

Reviews:

Related manuals for Solar-Log

Brands by name

Popular brands