Solare Datensysteme Solar-Log Components Connection Manual Download Page 43 | Manualshive

Page: 43 / 506

background image

43

Advanced Energy

5.3

Advanced Energy - AE-TX

Termination

Addressing

Interface

Jumper

Yes

RS485

Select “PVPowered” during the inverter detection.

Overview

•

Integrated interface.

•

Where to connect: Modbus Slave socket on interface card.

•

3-pin wiring.

•

Communication address must be allocated.

•

Installation steps:

•

Switch off the inverters and Solar-Log™.

•

Connect inverters to the Solar-Log™.

•

Set the address of the inverters.

•

Connect the inverters to each other.

Connect inverters to the Solar-Log™

The wiring is done using a

•

self-made 3 pin connection cable and terminal block connector.

Note

The transfer rate for Modbus (RS485) on delivery to the customer is set to 9600bps. Please check these
settings.

Procedure

1.  Open the inverter as shown in the inverter‘s instructions.
2.  Pull the free wires through the wire opening in the inverter.
3.  If you are making the cable yourself, connect the wires as shown in the following diagram:

Solar-Log™ terminal strip connector

RJ45 inverter

Terminal

PIN

►

1

►

2 - D+

►

3

►

1 - GND

►

4

►

3 - D-

4. If no further inverter connected, terminate the inverter.

Inside the inverter set the supplied jumper from „J4“ to „J5“.

5. Setting the address for the inverter: Set SW1 to „0“ and SW2 to „1“ in order to set the parameters for the inver-

ter with the address „01“.

6. Close the inverter if no other inverters are to be connected.
7. Insert the terminal block connector into the Solar-Log™ RS485 socket.

«
...
41
42
43
44
45
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

Brand: LogTag Recorders Pages: 46

Brand: Coollogger Pages: 30

Brand: Dostmann Electronic Pages: 17

Brand: B+B Sensors Pages: 19

Brand: u-blox Pages: 54

Brand: GasLab Pages: 2

Brand: Lascar Pages: 5

Pasport SPARKlink Air PS-2011

Brand: PASCO Pages: 3

Brand: Omega Pages: 24

Brand: MC Pages: 20

DataLogger 3 Series

Brand: Magnetek Pages: 2

Brand: Bosch Pages: 21

Brand: Xylem Pages: 15

ULTRASONIC Portable Mini

Brand: Calypso Pages: 10

Brand: Racelogic Pages: 2

Brand: Racelogic Pages: 13

Brand: Kaco Pages: 36

Brand: EasyLog Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands