Solare Datensysteme Solar-Log Components Connection Manual Download Page 344 | Manualshive

Page: 344 / 506

background image

344

Solutronic

91.2

Solutronic (SP)80, 100, 120, (SE)40S1, 40S2, 50S2, 60S2 (RS485)

Termination

Addressing

Interface

Yes

Yes

RS485

Note

The same protocol must be selected on both devices In order to ensure correct communication bet-
ween the Solar-Log™ and the inverters.

Protocol selection for device detection:

•

Solutronic: Protocol 1

•

Solutronic: Protocol 9

Overview

•

Integrated interface

•

Where to connect: Round pin plug on the outside of the inverter.

•

3-pin wiring

•

Communication address must be allocated.

•

All inverters must be fitted with firmware version 1.2.39 or later.

•

Inverters must be grounded otherwise this could lead to problems with inverter detection.

•

Installation steps

•

Switch off the inverters and Solar-Log™

•

Connect inverters to the Solar-Log™

•

Connect the inverters to each other

•

Allocate communication address

Connect inverters to the Solar-Log™

•

ready-made data cable (optional extra; not supplied)

or

•

self-made, shielded 3 wire data cable and terminal block connector.

Procedure

1. If you are making the cable yourself, connect the wires as shown in the following diagram:

Solar-Log™ terminal strip connector

Inverter terminal strip

Terminal

Terminal

►

1

►

2 - Data +

►

3

►

3 - Ground

►

4

►

4 - Data -

2. Terminate pin 1 on the terminal block connector and pin 4 on the Solar-Log

TM

using the 120

Ω

terminal resis-

tor.

3.  Terminate on the inverter in accordance with the manufacturer's handbook.
4.  Close the inverter if no other inverters are to be connected.
5.  Insert the terminal block connector into the Solar-Log™ RS485 socket.

«
...
342
343
344
345
346
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

Brand: LabJack Pages: 86

Brand: X2E Pages: 208

Brand: Turner Pages: 33

Brand: IBM Pages: 96

DataLogger 4 Series

Brand: Magnetek Pages: 28

Brand: Lascar Electronics Pages: 8

Minitrend QX Series

Brand: Honeywell Pages: 5

Brand: VOLTCRAFT Pages: 128

Brand: VOLTCRAFT Pages: 112

Brand: Thies CLIMA Pages: 56

Shimpo FG-7000L-S-5

Brand: Nidec Pages: 8

Brand: Egnite Pages: 102

Brand: Egnite Pages: 108

Brand: Egnite Pages: 130

Matman Combi-USB

Brand: ELTEX Pages: 2

Squirrel 1000 Series

Brand: Eltek Pages: 67

Brand: cloudworks Pages: 27

Brand: cloudworks Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands